A new method for actuating parallel manipulators

Abstract This paper presents a new technique of actuating a parallel platform manipulator using shape memory alloy (SMA). This is a type of smart materials that can attain a high strength-to-weight ratio, which makes them ideal for miniature application. The work is mainly to develop a new SMA actuator and then incorporating the actuator in building the parallel manipulator prototype. The SMA used in this study is a commercial NiTi wire. The SMA wire provides an actuating force that produces a large bending and end displacement. A 3-UPU (universal–prismatic–universal) parallel manipulator using linear SMA actuators was developed. The manipulator consists of a fixed platform, a moving platform and three SMA actuators. The manipulator workspace was specified based on the restrictions due to actuator strokes and joint angle limits. System identification techniques were used to model both heating and cooling processes. An ON/OFF control was performed and the results showed closeness in simulation and experimental results. This study showed that shape memory alloy actuated beam can successfully be used to provide linear displacement. The built prototype indicates the feasibility of using SMA actuators in parallel manipulators.

[1]  Yun-Jung Lee,et al.  Fast Preisach modeling method for shape memory alloy actuators using major hysteresis loops , 2004 .

[2]  Zhaowei Zhong,et al.  Development of a gripper using SMA wire , 2006 .

[3]  Hiroshi Yokoi,et al.  New Shape Memory Alloy Actuator: Design and Application in the Prosthetic Hand , 2005, 2005 IEEE Engineering in Medicine and Biology 27th Annual Conference.

[4]  Ingo Müller,et al.  Thermodynamics of pseudoelasticity —an analytical approach , 1993 .

[5]  Jean-Claude Latombe,et al.  Robot motion planning , 1970, The Kluwer international series in engineering and computer science.

[6]  Susumu Tachi,et al.  A method of autonomous locomotion for mobile robots , 1986, Adv. Robotics.

[7]  van der Arjan Schaft,et al.  Proceedings of the 44th IEEE Conference on Decision and Control, and European Control Conference, 2005 , 2005 .

[8]  Vincent Hayward,et al.  Constrained force control of shape memory alloy actuators , 2000, Proceedings 2000 ICRA. Millennium Conference. IEEE International Conference on Robotics and Automation. Symposia Proceedings (Cat. No.00CH37065).

[9]  Koji Ikuta,et al.  Development of shape-memory alloy actuators. Performance assessment and introduction of a new composing approach , 1988, Adv. Robotics.

[10]  L. Brinson,et al.  Shape memory alloys, Part I: General properties and modeling of single crystals , 2006 .

[11]  D. Stewart.  A Platform with Six Degrees of Freedom , 1965 .

[12]  Seung-Bok Choi,et al.  Position control of a parallel link manipulator using electro-rheological valve actuators , 2001 .

[13]  Rajnikant V. Patel,et al.  H∞Loop Shaping Controller for Shape Memory Alloy Actuators , 2005, Proceedings of the 44th IEEE Conference on Decision and Control.

[14]  Vincent Hayward,et al.  Design of shape memory alloy actuator with high strain and variable structure control , 1995, Proceedings of 1995 IEEE International Conference on Robotics and Automation.

[15]  Mohd Jailani Mohd Nor,et al.  A new concept of a linear smart actuator , 2007 .

[16]  James S. Albus,et al.  The NIST robocrane , 1993, J. Field Robotics.

[17]  Gregory S. Chirikjian,et al.  A binary paradigm for robotic manipulators , 1994, Proceedings of the 1994 IEEE International Conference on Robotics and Automation.

[18]  Masahiro Tsukamoto,et al.  Development of a shape memory alloy actuator. Measurement of material characteristics and development of active endoscopes , 1989, Adv. Robotics.

[19]  Kyoung Kwan Ahn,et al.  Position Control of Shape Memory Alloy Actuators by Using Self Tuning Fuzzy PID Controller , 2006, 2006 1ST IEEE Conference on Industrial Electronics and Applications.

[20]  Tae-hyun Nam,et al.  Fabrication of Ti-Ni alloys for proportional control , 2006 .