Tool Materials Rapid Selection Based on Initial Wear
暂无分享,去创建一个
[1] A. Senthil Kumar,et al. Wear behaviour of alumina based ceramic cutting tools on machining steels , 2006 .
[2] N. R. Dhar,et al. Effect of minimum quantity lubrication (MQL) on tool wear and surface roughness in turning AISI-4340 steel , 2006 .
[3] Wang Xi-bin. Wear Mechanism of Cemented Carbide Insert in Milling of High-strength Steel , 2005 .
[4] Gary W. Fischer,et al. A novel approach to quantifying tool wear and tool life measurements for optimal tool management , 2003 .
[5] Anselmo Eduardo Diniz,et al. Influence of the relative positions of tool and workpiece on tool life, tool wear and surface finish in the face milling process , 1999 .
[6] Liu Qiang. Partial Least Squares Regressive Analysis and Modeling for Tool Wear , 2000 .
[7] J. Paulo Davim,et al. Relationship between cutting force and PCD cutting tool wear in machining silicon carbide reinforced aluminium , 2000 .
[8] Kai Cheng,et al. Modeling flank wear of carbide tool insert in metal cutting , 2005 .
[9] F. Nabhani. Machining of aerospace titanium alloys , 2001 .
[10] M. Nouari,et al. Wear characteristics and performance of multi-layer CVD-coated alloyed carbide tool in dry end milling of titanium alloy , 2006 .
[11] G. Sur,et al. The effect of Al2O3, TiN and Ti (C,N) based CVD coatings on tool wear in machining metal matrix composites , 2004 .
[12] A. B. Chattopadhyay,et al. Growth of tool wear in turning of Ti-6Al-4V alloy under cryogenic cooling , 2007 .
[13] S. Veldhuis,et al. Elastic and plastic work of indentation as a characteristic of wear behavior for cutting tools with nitride PVD coatings , 2004 .
[14] Yongsheng Su,et al. An experimental investigation of effects of cooling/lubrication conditions on tool wear in high-speed end milling of Ti-6Al-4V , 2006 .
[15] Thomas R. Kurfess,et al. Quantification of tool wear using white light interferometry and three-dimensional computational metrology , 2005 .
[16] S. Veldhuis,et al. Effect of mechanical properties measured at room and elevated temperatures on the wear resistance of cutting tools with TiAlN and AlCrN coatings , 2006 .
[17] Yunhua Li. STUDY ON SENCOND-ORDER SLIDING MODE CONTROL LAW FOR ELECTRO-HYDRAULIC SERVO SYSTEM , 2005 .
[18] I. Jawahir,et al. Progressive tool-wear in machining with coated grooved tools and its correlation with cutting temperature , 2005 .
[19] J. Rigal,et al. Evolution during time of tool wear and cutting forces in the case of hard turning with CBN inserts , 2006 .
[20] XiaoQi Chen,et al. An experimental study of tool wear and cutting force variation in the end milling of Inconel 718 with coated carbide inserts , 2006 .
[21] Tuğrul Özel,et al. Predictive modeling of surface roughness and tool wear in hard turning using regression and neural networks , 2005 .
[22] Mahmudur Rahman,et al. Tool wear characteristics of binderless CBN tools used in high-speed milling of titanium alloys , 2005 .
[23] P. Arrazola,et al. Machinability of titanium alloys (Ti6Al4V and Ti555.3) , 2009 .
[24] Ahmed A. D. Sarhan,et al. Interrelationships between cutting force variation and tool wear in end-milling , 2001 .
[25] Yean-Liang Su,et al. Wear of CrC-coated carbide tools in dry machining , 2006 .
[26] Mohammed Nouari,et al. Tribo-energetic correlation of tool thermal properties to wear of WC-Co inserts in high speed dry machining of aeronautical grade titanium alloys , 2009 .
[27] Fu Gang Yan,et al. Cutting temperature and tool wear of hard turning hardened bearing steel , 2002 .
[28] P. S. Heyns,et al. An industrial tool wear monitoring system for interrupted turning , 2004 .
[29] Nabil Gindy,et al. An example of selection of the cutting conditions in broaching of heat-resistant alloys based on cutting forces, surface roughness and tool wear , 2005 .
[30] Ajay P. Malshe,et al. Tool wear and machining performance of cBN–TiN coated carbide inserts and PCBN compact inserts in turning AISI 4340 hardened steel , 2006 .
[31] Jianxin Deng,et al. Wear mechanisms of PVD ZrN coated tools in machining , 2008 .
[32] J. Paulo Davim,et al. Modelling of surface finish and tool flank wear in turning of AISI D2 steel with ceramic wiper inserts , 2007 .
[33] Tuğrul Özel,et al. Prediction of flank wear by using back propagation neural network modeling when cutting hardened H-13 steel with chamfered and honed CBN tools , 2002 .
[34] Philip Koshy,et al. Novel methods for rapid assessment of tool performance in milling , 2004 .