Characterization and acoustic emission monitoring of AFM nanomachining

This study aims to determine the machining characteristics during nano-scratching of silicon wafers using AFM and to monitor the machining states using acoustic emission (AE). Along with a specially designed AFM experimental setup, simplified geometric models are employed to estimate the friction coefficient and the minimum chip formation depth for nano-machining. In the nano-experiments, with the increase of the engaging depth of an AFM tip, two modes of plastic deformation—ploughing mode and cutting mode—are observed. With the aid of AFM and FE-SEM images, typical features of each mode, such as pile-up and chip formations, are illustrated and analyzed. Moreover, it is shown that pile-up formation is closely related to the deformation characteristics at the corresponding scratching depth, and the ratio of pile-ups to the groove depth can be used as an index to indicate the mode transition. As far as in-process monitoring is concerned, during the ploughing mode, related AE RMS values are relatively low. By contrast, the RMS values during the cutting mode are significantly higher than those during the ploughing mode, with apparent chip formation. In addition, AE count rates show appropriate sensitivity to detect the mode transition. Our results indicate that the proposed scheme can be used to characterize nano-scale machining and to monitor the mode transition.

[1]  Ulrich S Schubert,et al.  Nanolithography and nanochemistry: probe-related patterning techniques and chemical modification for nanometer-sized devices. , 2004, Angewandte Chemie.

[2]  Heh-Nan Lin,et al.  Fabrication of metal nanowires by atomic force microscopy nanoscratching and lift-off process , 2005 .

[3]  David Dornfeld,et al.  Monitoring of Ultraprecision Machining Processes , 2003 .

[4]  N. Umehara,et al.  Scratch–wear resistance of nanoscale super thin carbon nitride overcoat evaluated by AFM with a diamond tip , 2000 .

[5]  J. McGeough,et al.  Micromachining of Engineering Materials , 2001 .

[6]  N. Chandrasekaran,et al.  M.D. Simulation of nanometric cutting of single crystal aluminum–effect of crystal orientation and direction of cutting , 2000 .

[7]  Shen Dong,et al.  Investigation on AFM-based micro/nano-CNC machining system , 2007 .

[8]  Fengzhou Fang,et al.  Modelling and experimental investigation on nanometric cutting of monocrystalline silicon , 2005 .

[9]  Steven D. Kenny,et al.  Atomistic modelling of ploughing friction in silver, iron and silicon , 2006 .

[10]  S. Koshimizu,et al.  DETECTION OF DUCTILE TO BRITTLE TRANSITION IN MICROINDENTATION AND MICROSCRATCHING OF SINGLE CRYSTAL SILICON USING ACOUSTIC EMISSION , 2001 .

[11]  C. M. O. Valente,et al.  Precision Manufacturing Process Monitoring with Acoustic Emission , 2006 .

[12]  W. S. Blackley,et al.  Ductile-regime machining model for diamond turning of brittle materials , 1991 .

[13]  B. Bhushan,et al.  Micro/nanotribology of ultra-thin hard amorphous carbon coatings using atomic force/friction force microscopy , 1999 .

[14]  Bryan Kok Ann Ngoi,et al.  Ductile Regime Finish Machining - A Review , 2000 .

[15]  Bharat Bhushan,et al.  Nano- to microscale wear and mechanical characterization using scanning probe microscopy , 2001 .

[16]  Wei Gao,et al.  Experiments using a nano-machining instrument for nano-cutting brittle materials , 2000 .

[17]  Ichiro Inasaki,et al.  Sensor Fusion for Monitoring and Controlling Grinding Processes , 1999 .

[18]  K. Hokkirigawa,et al.  The effect of hardness on the transition of the abrasive wear mechanism of steels , 1988 .

[19]  D. Leea,et al.  Precision manufacturing process monitoring with acoustic emission , 2005 .

[20]  Seoung Hwan Lee,et al.  Precision Laser Deburring and Acoustic Emission Feedback , 2001 .

[21]  Vittorio Foglietti,et al.  Atomic force microscopy lithography as a nanodevice development technique , 1999 .

[22]  Hiroaki Tanaka,et al.  Towards a deeper understanding of wear and friction on the atomic scale—a molecular dynamics analysis , 1997 .

[23]  Tao Sun,et al.  Molecular dynamics simulation of processing using AFM pin tool , 2006 .

[24]  Wilma Polini,et al.  Monitoring of diamond disk wear in stone cutting by means of force or acceleration sensors , 2007 .

[25]  Jee-Gong Chang,et al.  Machining characterization of the nano-lithography process using atomic force microscopy , 2000 .

[26]  D. Dornfeld,et al.  Multi-Sensor Monitoring System in Chemical Mechanical Planarization (CMP) for Correlations with Process Issues , 2006 .

[27]  R. Scattergood,et al.  Ductile-Regime Grinding: A New Technology for Machining Brittle Materials , 1991 .

[28]  Herbert Kroemer,et al.  Direct patterning of surface quantum wells with an atomic force microscope , 1998 .