On the energy economics of air lubrication drag reduction

ABSTRACT Air lubrication techniques for frictional drag reduction on ships have been proposed by numerous researchers since the 19th century. However, these techniques have not been widely adopted as questions persist about their drag reduction performance beyond the laboratory, as well as energy and economic cost-benefit. This paper draws on data from the literature to consider the suitability of air lubrication for large ocean going and U.S. Great Lakes ships, by establishing the basic energy economic calculations and presenting results for a hypothetical air lubricated ship. All the assumptions made in the course of the analysis are clearly stated so that they can be refined when considering application of air lubrication to a specific ship. The analysis suggests that, if successfully implemented, both air layer and partial cavity drag reduction could lead to net energy savings of 10 to 20%, with corresponding reductions in emissions.

[1]  Mustafa Insel,et al.  Revisiting artificial air cavity concept for high speed craft , 2004 .

[2]  Richard Edwin Sonntag,et al.  Fundamentals of Thermodynamics , 1998 .

[3]  Steven Deutsch,et al.  Measurements of local skin friction in a microbubble-modified turbulent boundary layer , 1985, Journal of Fluid Mechanics.

[4]  Simo A. Mäkiharju.  The Dynamics of Ventilated Partial Cavities over a Wide Range of Reynolds Numbers and Quantitative 2D X-ray Densitometry for Multiphase Flow , 2012 .

[5]  Konstantin I. Matveev,et al.  On the limiting parameters of artificial cavitation , 2003 .

[6]  M. P. Teterin.  Study of gas flow and heat transfer in region of incidence of a compression shock on a cylinder in a high supersonic stream , 1967 .

[7]  S. Ceccio.  Friction Drag Reduction of External Flows with Bubble and Gas Injection , 2010 .

[8]  David R. Dowling,et al.  Bubble-induced skin-friction drag reduction and the abrupt transition to air-layer drag reduction , 2008, Journal of Fluid Mechanics.

[9]  Hamid Amini,et al.  Ship Hull Drag Reduction Using Bottom Air Injection , 2007 .

[10]  Simo A. Mäkiharju,et al.  Perturbed Partial Cavity Drag Reduction at High Reynolds Numbers , 2010 .

[11]  C. Kawakita.  Experimental Study of Air Lubrication Method and Verification of Effects on Actual Hull by Means of Sea Trial , 2010 .

[12]  Michael G. Parsons,et al.  Integrated electric plants in future Great Lakes self-unloaders , 2011 .

[13]  Roger E. A. Arndt,et al.  Creation and Maintenance of Cavities Under Horizontal Surfaces in Steady and Gust Flows , 2009 .

[14]  Yoshiaki Kodama,et al.  A Research Project on Application of Air Bubble Injection to a Full Scale Ship for Drag Reduction , 2007 .

[15]  Jung-Lyul Lee,et al.  An array effect of wave energy farm buoys , 2012 .

[16]  C. L. Hoang,et al.  Full Scale Experiment For Frictional Resistance Reduction Using Air Lubrication Method , 2009 .

[17]  Chang-li Yu,et al.  Ultimate strength of simply supported plate with opening under uniaxial compression , 2012 .

[18]  A. A. Butuzov.  Artificial cavitation flow behind a slender wedge on the lower surface of a horizontal wall , 1967 .

[19]  Simo A. Mäkiharju,et al.  Partial cavity drag reduction at high reynolds numbers , 2010 .

[20]  Eduard Amromin,et al.  Partial Cavitation as Drag Reduction Technique and Problem of Active Flow Control , 2003 .

[21]  Y. Kodama,et al.  EXPERIMENTAL STUDY ON MICROBUBBLES AND THEIR APPLICABILITY TO SHIPS FOR SKIN FRICTION REDUCTION , 2000, Proceeding of First Symposium on Turbulence and Shear Flow Phenomena.

[22]  David R. Dowling,et al.  Bubble friction drag reduction in a high-Reynolds-number flat-plate turbulent boundary layer , 2006, Journal of Fluid Mechanics.

[23]  K.-S. Choi,et al.  Emerging techniques in drag reduction , 1996 .

[24]  R H Miller.  GREAT LAKES THOUSAND FOOTERS , 1979 .