The path of rolling elements in defective bearings: Observations, analysis and methods to estimate spall size

Abstract This paper describes the experimental investigation of the vibration signature generated by rolling elements entering and exiting a notch defect in the outer raceway of a bearing. The vibration responses of the bearing housing and the displacement between the raceways were measured and analyzed. These key features can be used to estimate the size of the defect and is demonstrated in this paper for a range of shaft speeds and bearing loads. It is shown that existing defect size estimation methods include assumptions that describe the path of the rolling elements in the defect zone leading to poor estimates of defect size. A new defect size estimation method is proposed and is shown to be accurate for estimating a range of notch defect geometries over a range of shaft speeds and applied loads.

[1]  Bin Zhang,et al.  A Probabilistic Fault Detection Approach: Application to Bearing Fault Detection , 2011, IEEE Transactions on Industrial Electronics.

[2]  Y.-T. Su,et al.  The Effects of Surface Irregularities on Roller Bearing Vibrations , 1993 .

[3]  Aki Mikkola,et al.  Dynamic model of a deep-groove ball bearing including localized and distributed defects. Part 1: Theory , 2003 .

[4]  A. Ahmadi,et al.  Analysis of bearing stiffness variations, contact forces and vibrations in radially loaded double row rolling element bearings with raceway defects , 2015 .

[5]  P. K. Kankar,et al.  Stability analysis of a rotor bearing system due to surface waviness and number of balls , 2004 .

[6]  Robert B. Randall,et al.  Simulating gear and bearing interactions in the presence of faults Part II. Simulation of the vibrations produced by extended bearing faults , 2008 .

[7]  Ravi Prakash,et al.  The effect of speed of balanced rotor on nonlinear vibrations associated with ball bearings , 2003 .

[8]  Carl Q. Howard,et al.  A nonlinear dynamic model of the vibration response of defective rolling element bearings , 2013 .

[9]  C. S. Sunnersjö.  Rolling bearing vibrations—The effects of geometrical imperfections and wear , 1985 .

[10]  Lin Liang,et al.  Quantitative diagnosis of a spall-like fault of a rolling element bearing by empirical mode decomposition and the approximate entropy method , 2013 .

[11]  S. Marble,et al.  Validating Prognostic Algorithms: A Case Study Using Comprehensive Bearing Fault Data , 2007, 2007 IEEE Aerospace Conference.

[12]  Robert B. Randall,et al.  Simulating gear and bearing interactions in the presence of faults. Part I. The combined gear bearing dynamic model and the simulation of localised bearing faults , 2008 .

[13]  Carl Q. Howard,et al.  Varying stiffness and load distributions in defective ball bearings: Analytical formulation and application to defect size estimation , 2015 .

[14]  Robert B. Randall,et al.  Vibration response of spalled rolling element bearings: Observations, simulations and signal processing techniques to track the spall size , 2011 .

[15]  S. Harsha.  Nonlinear dynamic analysis of a high-speed rotor supported by rolling element bearings , 2006 .

[16]  S. P. Harsha,et al.  Nonlinear dynamic analysis of an unbalanced rotor supported by roller bearing , 2005 .

[17]  Sadok Sassi,et al.  A Numerical Model to Predict Damaged Bearing Vibrations , 2007 .

[18]  Aki Mikkola,et al.  Dynamic model of a deep-groove ball bearing including localized and distributed defects. Part 2: Implementation and results , 2003 .

[19]  Miha Boltežar,et al.  Improved model of a ball bearing for the simulation of vibration signals due to faults during run-up , 2011 .

[20]  S. Harsha,et al.  Non-linear dynamic behaviors of rolling element bearings due to surface waviness , 2004 .

[21]  N. Tandon,et al.  A theoretical model to predict the vibration response of rolling bearings in a rotor bearing system to distributed defects under radial load , 2000 .

[22]  N. Tandon,et al.  A Theoretical Model to Predict Vibration Response of Rolling Bearings to Distributed Defects Under Radial Load , 1998 .

[23]  Carl Q. Howard,et al.  A nonlinear dynamic vibration model of defective bearings – The importance of modelling the finite size of rolling elements , 2015 .

[24]  T. A. Harris,et al.  Rolling Bearing Analysis , 1967 .

[25]  Carl Q. Howard,et al.  Analyses of contact forces and vibration response for a defective rolling element bearing using an explicit dynamics finite element model , 2014 .

[26]  M. Cao,et al.  A comprehensive dynamic model of double-row spherical roller bearing—Model development and case studies on surface defects, preloads, and radial clearance , 2008 .