Measurement and CFD Prediction of Heat Transfer in Air-Cooled Disc-Type Electrical Machines

Accurate thermal analysis of axial flux permanent magnet (AFPM) machines is crucial in predicting maximum power output. Stator convective heat transfer is one of the most important and least investigated heat transfer mechanisms and is the focus of this paper. Experimental measurements were undertaken using a thin-film electrical heating method, providing radially resolved steady state heat transfer data from an experimental rotor-stator system designed as a geometric mockup of a through-flow ventilated AFPM machine. The measurements are compared with computational fluid dynamics (CFD) simulations using both 2-D axisymmetric and 3-D models. These were found to give a conservative estimate of heat transfer, with inaccuracies near the edge and in the transitional flow regime. Predicted stator heat transfer was found to be relatively insensitive to the choice of turbulence model used in the CFD simulations.

[1]  Neil Brown,et al.  Air flow and heat transfer modeling of an Axial Flux Permanent Magnet Generator , 2009 .

[2]  M.J. Kamper,et al.  Development of a thermofluid model for Axial field permanent-magnet Machines , 2005, IEEE Transactions on Energy Conversion.

[3]  N. Saniei,et al.  Turbulent heat transfer on the stationary disk in a rotor-stator system , 2003 .

[4]  Maarten J. Kamper,et al.  Thermal modelling of an axial flux permanent magnet machine , 2004 .

[5]  F. Menter,et al.  A Correlation-Based Transition Model Using Local Variables: Part I — Model Formulation , 2004 .

[6]  J. Owen,et al.  Heat transfer from an air-cooled rotating disk , 1974, Proceedings of the Royal Society of London. A. Mathematical and Physical Sciences.

[7]  N. Gregory,et al.  On the stability of three-dimensional boundary layers with application to the flow due to a rotating disk , 1955, Philosophical Transactions of the Royal Society of London. Series A, Mathematical and Physical Sciences.

[8]  F. Menter.  Two-equation eddy-viscosity turbulence models for engineering applications , 1994 .

[9]  Andrew S. Holmes,et al.  Air-Gap Convection in Rotating Electrical Machines , 2012, IEEE Transactions on Industrial Electronics.

[10]  K. Pullen,et al.  Measurement of stator heat transfer in air-cooled axial flux permanent magnet machines , 2009, 2009 35th Annual Conference of IEEE Industrial Electronics.

[11]  K. Pullen,et al.  Radially resolved measurement of stator heat transfer in a rotor-stator disc system , 2010 .

[12]  Jacek F. Gieras,et al.  Axial Flux Permanent Magnet Brushless Machines , 2005 .

[13]  Hector Iacovides,et al.  The computation of convective heat transfer in rotating cavities , 1993 .

[14]  K. Mahkamov,et al.  Computations on heat transfer in axial flux permanent magnet machines , 2008, 2008 18th International Conference on Electrical Machines.

[15]  S. Wittig,et al.  Local Heat Transfer in Turbine Disk-Cavities: Part I — Rotor and Stator Cooling With Hub Injection of Coolant , 1990 .

[16]  K. Mahkamov,et al.  2-D lumped-parameter thermal modelling of axial flux permanent magnet generators , 2008, 2008 18th International Conference on Electrical Machines.

[17]  D. R. Turner,et al.  Lumped parameter thermal model for electrical machines of TEFC design , 1991 .

[18]  S. Harmand,et al.  Local convective heat transfer for laminar and turbulent flow in a rotor-stator system , 2005 .

[19]  Sébastien Poncet,et al.  Batchelor versus Stewartson flow structures in a rotor-stator cavity with throughflow , 2005 .

[20]  O. Daube,et al.  Axisymmetric numerical simulations of turbulent flow in rotor stator enclosures , 2002 .