Experimental Evaluation of Lubrication Characteristics of a New Type Oil-Film Bearing Oil Using Multi-Sensor System

In order to evaluate the operating performance of a new type oil-film bearing oil S220, a new test bearing was designed based on oil-film bearing test rig. The operating temperature of S220 was tested through the thermocouples installed on a test bearing; the operating oil-film pressure was tested through pressure transducers; and the operating oil-film thickness was tested through displacement transducers. Meanwhile, M220 was also tested as a comparison, and both oils are based on mineral oil. The results showed that all property indexes of the test rig can meet the specified requirements and can guarantee the performance test of oil-film bearing oil; the operating temperature of S220 is generally equal to that of M220, and both have the same operating stability. The temperature property conforms to Formula (1) and the operating temperature under different load cases can be predicted. Although oil-film pressure of M220 is a little more stable, the oil-film pressure of S220 is similar to that of M220. Moreover, both have the similar oil-film thickness, and the oil-film thickness of S220 is slightly smaller than that of M220, especially at the beginning of operation. Ultimately, oil S220 is evaluated to be suitable for actual engineering application.

[1]  Michel Fillon,et al.  Experimental measurement of the friction torque on hydrodynamic plain journal bearings during start-up , 2011 .

[2]  Sergei Glavatskih,et al.  Simultaneous monitoring of oil film thickness and temperature in fluid film bearings , 2000 .

[3]  R. Fan,et al.  Enhancing AW/EP property of lubricant oil by adding nano Al/Sn particles , 2005 .

[4]  Ramiro C. Martins,et al.  Gear power loss performance of biodegradable low-toxicity ester-based oils , 2008 .

[5]  P. G. Morton,et al.  Paper XI(ii) The influence of grooves in bearings on the stability and response of rotating systems , 1987 .

[6]  J. M. Perez,et al.  Sequential four-ball study of some lubricating oils© , 1999 .

[7]  Kenshi Ushijima,et al.  A Measurement of Oil Film Pressure Distribution in Connecting Rod Bearing With Test Rig , 1992 .

[8]  Jia Xu,et al.  A New Fitting Scattered Data Method based on the Criterion of Geometric Distance , 2012 .

[9]  Paul E. Allaire,et al.  A New Fluid Film Bearing Test Rig for Oil and Water Bearings , 2008 .

[10]  Xin Zhang,et al.  Modeling of nonlinear system based on deep learning framework , 2016 .

[11]  Reza Malekian,et al.  Electrical Anisotropic Response of Water Conducted Fractured Zone in the Mining Goaf , 2016, IEEE Access.

[12]  Qing-xue Huang,et al.  PRESSURE DISTRIBUTION AND DAMAGES OF OIL-FILM BEARING SLEEVE DURING THE PROCESS OF INTERFERENCE FIT , 2006 .

[13]  S. N. Kudryavtsev,et al.  Russian Lubricating Oils for Rolling Mills with Fluid-Friction Bearings , 2005 .

[14]  Tao Chen,et al.  Secure Two-Party Distance Computation Protocol Based on Privacy Homomorphism and Scalar Product in Wireless Sensor Networks , 2016 .

[15]  Su Jian,et al.  The automobile engine lubricating oil monitor engineering research based on the near-infrared light method , 2011, 2011 International Conference on Consumer Electronics, Communications and Networks (CECNet).

[16]  Wang Jianmei,et al.  Viscosity monitoring and control on oil-film bearing lubrication with ferrofluids , 2014 .

[17]  Sergei Glavatskih,et al.  Synthetic Lubricants in Hydrodynamic Journal Bearings: Experimental Results , 2011 .

[18]  Jiun-Wei Horng,et al.  Differential Second-Order Voltage-Mode All-Pass Filter Using Current Conveyors , 2016 .

[19]  Michel Fillon,et al.  Influence of lubricants on plain bearing performance: Evaluation of bearing performance with polymer-containing oils , 2012 .

[20]  A. G. Souza,et al.  Thermal, spectroscopic and rheological study of mineral base lubricating oils , 2007 .

[21]  M. C. Jones,et al.  Relative error prediction via kernel regression smoothers , 2008 .

[22]  Reza Malekian,et al.  An Improved Time-Frequency Representation Based on Nonlinear Mode Decomposition and Adaptive Optimal Kernel , 2016 .

[23]  Jolanta Drabik,et al.  Modelling relation between oxidation resistance and tribological properties of non-toxic lubricants with the use of artificial neural networks , 2012, Journal of Thermal Analysis and Calorimetry.

[24]  Michael M. Khonsari,et al.  Experimental testing and thermal analysis of ball bearings , 2013 .

[25]  A Sasaki,et al.  Contaminants in Used Oils and Their Problems , 2006 .

[26]  Michel Fillon,et al.  Experimental comparison of the performance of a journal bearing with a single and a twin axial groove configuration , 2012 .

[27]  Mehmet Sari,et al.  An improved method of fitting experimental data to the Hoek–Brown failure criterion , 2012 .

[28]  Ning Wang,et al.  Theoretical and experimental investigation on the thermal characteristics of double-row tapered roller bearings of high speed locomotive , 2015 .

[29]  Qing Xue Huang,et al.  Design and Development of Hydrodynamic Lubricating System of Large-Scale Mill Oil-Film Bearing Test Rig , 2010 .