Influence of TiO2 nanoparticles addition on the microstructural and mechanical properties of Sn0.7Cu nano-composite solder

Abstract Composites of SC solder reinforced with 0, 0.25, 0.5 and 1 wt.% of TiO2 nanoparticles were fabricated using a mechanical technique. With increased addition of TiO2 nanoparticles, the SC nano-composite solder was found to have a slightly lower melting temperature. The addition of TiO2 nanoparticles can also effectively refine the microstructure as so β-Sn and Cu6Sn5, and increase the percentage of eutectic area. The mechanical properties (microhardness, 0.2% YS and UTS) increase with the increasing presence of reinforcement, far exceeding the strength of the eutectic SC solder. The yield strength improvement was attributed to (i) the Hall–Petch effect due to β-Sn grain size refinement. (ii) Orowan strengthening, (iii) generation of geometrically necessary dislocations to accommodate CTE mismatch between the matrix and the second phase (Cu6Sn5 and TiO2), and (iv) the load-bearing effects due to the presence of nano-sized reinforcements.

[1]  R. W. Wu,et al.  Interfacial reactions between liquid Sn3.5Ag0.5Cu solders and Ag substrates , 2011 .

[2]  Zhigang Chen,et al.  Effect of rare earth element additions on the microstructure and mechanical properties of tin-silver-bismuth solder , 2002 .

[3]  W. D. Kingery,et al.  Introduction to Ceramics , 1976 .

[4]  C. J. Fang,et al.  Effect of nano-TiO2 addition on the microstructure and bonding strengths of Sn3.5Ag0.5Cu composite solder BGA packages with immersion Sn surface finish , 2011 .

[5]  Q. Zhang,et al.  A model for predicting the particle size dependence of the low cycle fatigue life in discontinuously reinforced MMCs , 2004 .

[6]  S. Yen,et al.  Intermetallic reactions in Sn3Ag0.5Cu and Sn3Ag0.5Cu0.06Ni0.01Ge solder BGA packages with Au/Ni surface finishes , 2006 .

[7]  Yi-long Bai,et al.  Size-dependent inelastic behavior of particle-reinforced metal–matrix composites , 2001 .

[8]  Kenneth E. Lulay,et al.  Strengthening of a particulate metal matrix composite by quenching , 1991 .

[9]  Ping Liu,et al.  Effect of SiC Nanoparticle Additions on Microstructure and Microhardness of Sn-Ag-Cu Solder Alloy , 2008 .

[10]  S. Y. Chang,et al.  Effect of addition of TiO2 nanoparticles on the microstructure, microhardness and interfacial reactions of Sn3.5AgXCu solder , 2011 .

[11]  M. Gupta,et al.  Development of lead-free Sn–0.7Cu/Al2O3 nanocomposite solders with superior strength , 2008 .

[12]  Z. Zhang,et al.  Contribution of Orowan strengthening effect in particulate-reinforced metal matrix nanocomposites , 2008 .

[13]  S. Y. Chang,et al.  Effects of Nano-TiO2 additions on thermal analysis, microstructure and tensile properties of Sn3.5Ag0.25Cu solder , 2010 .

[14]  Y. C. Chan,et al.  Microstructure, kinetic analysis and hardness of Sn–Ag–Cu–1 wt% nano-ZrO2 composite solder on OSP-Cu pads , 2011 .

[15]  C. Chien,et al.  Synthesis and characterization of particle-reinforced Ni/Al_2O_3 nanocomposites , 2002 .

[16]  V. Kripesh,et al.  Influence of single-wall carbon nanotube addition on the microstructural and tensile properties of Sn–Pb solder alloy , 2008 .

[17]  M. Ashby,et al.  Metallic glasses as structural materials , 2006 .

[18]  J. Wei,et al.  Improving the performance of lead-free solder reinforced with multi-walled carbon nanotubes , 2006 .

[19]  Fu Guo,et al.  Creep property of composite solders reinforced by nano-sized particles , 2008 .

[20]  L. Tsao,et al.  AgIn2/Ag2In transformations in an In-49Sn/Ag soldered joint under thermal aging , 2001 .

[21]  Hiroshi Nishikawa,et al.  Interfacial reaction between Sn-0.7Cu (-Ni) solder and Cu substrate , 2006 .

[22]  L. Tsao,et al.  Effect of TiO2 nanoparticles on the microstructure and bonding strengths of Sn0.7Cu composite solder BGA packages with immersion Sn surface finish , 2012, Journal of Materials Science: Materials in Electronics.

[23]  L. Tsao,et al.  An investigation of microstructure and mechanical properties of novel Sn3.5Ag0.5Cu–XTiO2 composite solders as functions of alloy composition and cooling rate , 2011 .

[24]  S. Y. Chang,et al.  Effects of nano-Al2O3 additions on microstructure development and hardness of Sn3.5Ag0.5Cu solder , 2010 .

[25]  J. Coleman,et al.  Morphological and mechanical properties of carbon-nanotube-reinforced semicrystalline and amorphous polymer composites , 2002 .

[26]  M. Véron,et al.  Deformation mechanism in high strength Cu/Nb nanocomposites , 2001 .

[27]  R. Mahmudi,et al.  High-temperature shear strength of lead-free Sn–Sb–Ag/Al2O3 composite solder , 2011 .

[28]  L. Tsao.  Evolution of nano-Ag3Sn particle formation on Cu–Sn intermetallic compounds of Sn3.5Ag0.5Cu composite solder/Cu during soldering , 2011 .

[29]  W. D. Callister,et al.  Fundamentals of Materials Science and Engineering , 2004 .