This chapter presents the design and development of thin-film LCP surface mount (SMT) package feed-throughs for DC to Ka-band applications. Three types of feed-through design will be introduced, via feed, bandpass feed, and lumped element feed, that interface signals from the outside world to a component inside a package. The packages are constructed using multilayer LCP films and are surface mounted on a printed circuit board (PCB) for use. The utilization of an all-LCP enclosure provides a hermetic environment for microwave and millimetre-wave monolithic integrated circuits (MMICs). In addition, mounting MMICs inside a package cavity allows enhanced thermal dissipation because the metal submounts can make direct contact with the PCB or motherboard ground through solder or epoxy. Applications that require lightweight, hermetic, and low-loss modules, which can be developed using LCP, include, but are not limited to, vehicular-collision-warning short-range radar, radar for ground-moving vehicles, point-to-point communication, ground–satellite communication, intersatellite links, and airborne radar. A phased-array system for ground-vehicle or airborne applications may require thousands of modules in the RF link. If each module, typically cased in ceramic and metal, were replaced with LCP packages, then the total weight of a system could be reduced by more than 66%, because ceramic [1] is three times denser than LCP [2]; this can lead to improvements in fuel efficiency. Section 5.1 shows the design, the modeling, and measurement process of a Ka-band package feed-through using vias. The experimental results demonstrate that a package via feed-through including a PCB signal launch structure and bond wires achieves a return loss of better than 20 dB and an insertion loss of less than 0.4 dB at the Ka-band. The package has a measured port-to-port isolation greater than 45 dB up to 40 GHz. An amplifier packaged inside an LCP SMT package is characterized. The measured data are then compared with a circuit-model simulation of the package feed-through, using the on-wafer data of an amplifier to validate the lumped-circuit model.
[1]
R. Collin.
Foundations for microwave engineering
,
1966
.
[2]
H. R. Kaupp,et al.
Characteristics of Microstrip Transmission Lines
,
1967,
IEEE Trans. Electron. Comput..
[3]
V. Tripathi.
Asymmetric Coupled Transmission Lines in an Inhomogeneous Medium
,
1975
.
[4]
Darko Kajfez,et al.
Design Equations for Symmetric Microstrip DC Blocks
,
1980
.
[5]
T. C. Edwards,et al.
Foundations for microstrip circuit design
,
1981
.
[6]
Reinmut K. Hoffmann,et al.
Handbook of microwave integrated circuits
,
1987
.
[7]
E. Bogatin,et al.
Design rules for microstrip capacitance
,
1988
.
[8]
Robert E. Canright.
A simple formula for dual stripline characteristic impedance
,
1990,
IEEE Proceedings on Southeastcon.
[9]
D. Pozar.
Microwave Engineering
,
1990
.
[10]
G. Matthaei,et al.
Experimental analysis of transmission line parameters in high-speed GaAs digital circuit interconnects
,
1991
.
[11]
R. Pucel,et al.
Modeling via hole grounds in microstrip
,
1991,
IEEE Microwave and Guided Wave Letters.
[12]
J. Laskar,et al.
Development of On-Wafer Microstrip Characterization Techniques
,
1996,
47th ARFTG Conference Digest.
[13]
Kai Chang,et al.
Microwave Ring Circuits and Antennas
,
1996
.
[14]
L. Chai,et al.
LTCC for wireless and photonic packaging applications
,
2002,
Proceedings of the 4th International Symposium on Electronic Materials and Packaging, 2002..
[15]
Mingwei Li,et al.
Micromachining of liquid crystal polymer film with frequency converted diode-pumped Nd:YVO4 laser
,
2003,
SPIE LASE.
[16]
Anh-Vu Pham,et al.
Development of Thin-Film Liquid Crystal Polymer Surface Mount Packages for Ka-band Applications
,
2006,
2006 IEEE MTT-S International Microwave Symposium Digest.
[17]
S. Nelson,et al.
Development of LCP surface mount package with a bandpass feedthrough at K-band
,
2008,
2008 IEEE MTT-S International Microwave Symposium Digest.