Comparison of injection molding process windows for plastic lens established by artificial neural network and response surface methodology

This study used artificial neural network (ANN) and response surface methodology (RSM) to obtain the lens form accuracy prediction model. Moreover, it established the operating parameter region that satisfies the designated lens form accuracy at a minimum cost. Finally, experimental verification and accuracy comparison were conducted. This study used the Taguchi method for parameter screening experiment in the injection molding process. The obtained significant factors that influence form accuracy of the lens were mold temperature, cooling time, and packing time. Those significant factors were used for full factorial experiment, for adjusted experiment using composite central design method, and to establish the process window. According to the results, the process window for injection molding using an ANN to establish cooling time and packing time was a high-order, irregular shape, whereas the one established by a RSM was oblique oval. The optimal form accuracy of the lens obtained from ANN model was better than that from RSM model. The result of the experiment indicated that the process window of the injection molding process for optimal form accuracy obtained from both ANN and RSM models is quite consistent. In addition, a case study for a form accuracy of 0.5 μm was discussed. The process window established by ANN had a better accuracy and wider range than that by RSM.

[1]  Joanne Yip,et al.  Parametric design and process parameter optimization for bra cup molding via response surface methodology , 2012, Expert Syst. Appl..

[2]  Warpage phenomenon of thin-wall injection molding , 2011 .

[3]  K. S. Lee,et al.  Design of the runner and gating system parameters for a multi-cavity injection mould using FEM and neural network , 2006 .

[4]  Kuo-Ming Tsai,et al.  Determination of injection molding process window based on form accuracy of lens using response surface methodology , 2014 .

[5]  C. J. Yang,et al.  Optimising the thermoforming process of polymeric foams: an approach by using the Taguchi method and the utility concept , 2004 .

[6]  Deniz Baş,et al.  Modeling and optimization I: Usability of response surface methodology , 2007 .

[7]  Chiaming Yen,et al.  An abductive neural network approach to the design of runner dimensions for the minimization of wrappage in injection mouldings , 2006 .

[8]  Mohan Kumar Pradhan,et al.  Estimating the effect of process parameters on surface integrity of EDMed AISI D2 tool steel by response surface methodology coupled with grey relational analysis , 2013 .

[9]  W. B. Bae,et al.  Application of neural network and computer simulation to improve surface profile of injection molding optic lens , 2005 .

[10]  Guoqun Zhao,et al.  Research on optimization design of the heating/cooling channels for rapid heat cycle molding based on response surface methodology and constrained particle swarm optimization , 2011, Expert Syst. Appl..

[11]  Jie-Ren Shie,et al.  Optimization of injection molding process for contour distortions of polypropylene composite components by a radial basis neural network , 2008 .

[12]  Chih-Hung Tsai,et al.  A study of optimization of injection molding process parameters for SGF and PTFE reinforced PC composites using neural network and response surface methodology , 2012 .

[13]  Amar Patnaik,et al.  Optimization of wire electrical discharge machining (WEDM) process parameters using Taguchi method , 2007 .

[14]  Vladimir Modrak,et al.  Investigation of the influence of technological parameters on surface color of plastic parts , 2013, The International Journal of Advanced Manufacturing Technology.

[15]  Yusuf Kaynak,et al.  Influence of molding conditions on the shrinkage and roundness of injection molded parts , 2010 .

[16]  Mirigul Altan,et al.  Reducing shrinkage in injection moldings via the Taguchi, ANOVA and neural network methods , 2010 .

[17]  Wen-Chin Chen,et al.  An integrated parameter optimization system for MISO plastic injection molding , 2009 .

[18]  T. Rouxel,et al.  Influence of Grinding Parameters on Glass Workpieces Surface Finish Using Response Surface Methodology , 2011 .

[19]  Hasan Öktem,et al.  Optimum process conditions on shrinkage of an injected-molded part of DVD-ROM cover using Taguchi robust method , 2012 .

[20]  D. Lizotte,et al.  An experimental methodology for response surface optimization methods , 2012, J. Glob. Optim..

[21]  Douglas C. Montgomery,et al.  Response Surface Methodology: Process and Product Optimization Using Designed Experiments , 1995 .

[22]  N. Ismail,et al.  The use of Taguchi method in the design of plastic injection mould for reducing warpage , 2007 .

[23]  Hongsheng Li,et al.  Reducing the effects of weldlines on appearance of plastic products by Taguchi experimental method , 2007 .

[24]  Chong-Ching Chang,et al.  Optimal-Parameter Determination by Inverse Model Based on MANFIS: The Case of Injection Molding for PBGA , 2011, IEEE Transactions on Control Systems Technology.

[25]  Genichi Taguchi,et al.  Taguchi's Quality Engineering Handbook , 2004 .

[26]  Kuo-Ming Tsai.  Effect of injection molding process parameters on optical properties of lenses , 2010 .

[27]  Chao-Chang A. Chen,et al.  Automated surface finishing of plastic injection mold steel with spherical grinding and ball burnishing processes , 2006 .

[28]  B.H.M. Sadeghi,et al.  A BP-neural network predictor model for plastic injection molding process , 2000 .

[29]  L. Hua,et al.  A hybrid of back propagation neural network and genetic algorithm for optimization of injection molding process parameters , 2011 .

[30]  Chih-Cherng Chen,et al.  Analysis and modeling of effective parameters for dimension shrinkage variation of injection molded part with thin shell feature using response surface methodology , 2009 .

[31]  Keun Park,et al.  A Study on Flow Simulation and Deformation Analysis for Injection-Molded Plastic Parts Using Three-Dimensional Solid Elements , 2005 .

[32]  Hasan Kurtaran,et al.  Efficient warpage optimization of thin shell plastic parts using response surface methodology and genetic algorithm , 2006 .

[33]  Ko-Ta Chiang,et al.  Analysis of shrinkage and warpage in an injection-molded part with a thin shell feature using the response surface methodology , 2007 .