Mobilized thermal energy storage: Materials, containers and economic evaluation

Abstract The transportation of thermal energy is essential for users who are located far away from heat sources. The networks connecting them achieve the goal in efficient heat delivery and reasonable cost, especially for the users with large heat demands. However, it is difficult to satisfy the heat supply of the detached or emergent users with the existing pipelines. Therefore, a promising alternative, called mobilized thermal energy storage (M-TES), was proposed to deliver the heat flexibly without the restriction of networks. In this paper, a review of studies on M-TES is conducted in terms of materials, containers and economic evaluation. The potential candidates of materials, such as sugar alcohols, hydrated salts, alkalies and zeolite are reviewed and compared based on their thermophysical properties, price, advantages and disadvantages. Various containers, including the shell-and-tube, encapsulated, direct-contact, detachable and sorptive types, are discussed from the aspects of configuration, performance and utilization. Furthermore, the studies on the economic evaluation of M-TES systems are summarized and discussed based on the analysis of the economic indicators, including initial cost, operating cost, revenue, subsidy and energy cost. Finally, the challenges and future perspectives for developing M-TES are presented.

[1]  Dieter Brüggemann,et al.  Thermophysical Characterization of MgCl2·6H2O, Xylitol and Erythritol as Phase Change Materials (PCM) for Latent Heat Thermal Energy Storage (LHTES) , 2017, Materials.

[2]  Tong Zhu,et al.  Modeling and optimization for hydraulic performance design in multi-source district heating with fluctuating renewables , 2018 .

[3]  J. Danielewicz,et al.  Trends of European research and development in district heating technologies , 2017 .

[4]  Yulong Ding,et al.  Comparative study of the transient natural convection in an underground water pit thermal storage , 2017 .

[5]  Cong-Toan Tran,et al.  Dynamic modeling for evaluation of triple-pipe configuration potential in geothermal district heating networks , 2018, Energy Conversion and Management.

[6]  Jesús Lizana,et al.  Advances in thermal energy storage materials and their applications towards zero energy buildings: A critical review , 2017 .

[7]  David R. Mills,et al.  Screening of high melting point phase change materials (PCM) in solar thermal concentrating technology based on CLFR , 2005 .

[8]  Jun Zhao,et al.  Numerical study of the improvement of an indirect contact mobilized thermal energy storage container , 2016 .

[9]  Wasim Saman,et al.  Development of a novel refrigeration system for refrigerated trucks incorporating phase change material , 2012 .

[10]  Alain Sommier,et al.  Characterization of different sugar alcohols as phase change materials for thermal energy storage applications , 2017 .

[11]  Erwin P. Ona,et al.  Influence of Ultrasonic Irradiation on the Solidification Behavior of Erythritol as a PCM , 2002 .

[12]  Luisa F. Cabeza,et al.  Thermal behaviour of d-mannitol when used as PCM: Comparison of results obtained by DSC and in a thermal energy storage unit at pilot plant scale , 2013 .

[13]  Ryoichi Yamamoto,et al.  Heat storage capacity of sodium acetate trihydrate during thermal cycling , 1984 .

[14]  Nobuhiro Maruoka,et al.  Thermal and flow behaviors in heat transportation container using phase change material , 2008 .

[15]  M. Kenisarin,et al.  Salt hydrates as latent heat storage materials:Thermophysical properties and costs , 2016 .

[16]  Weiwen Xu,et al.  Study on phase change interface for erythritol with nano-copper in spherical container during heat transport , 2016 .

[17]  Luisa F. Cabeza,et al.  Stability of sugar alcohols as PCM for thermal energy storage , 2014 .

[18]  Andreas Hauer,et al.  Mobile Sorption Heat Storage in Industrial Waste Heat Recovery , 2015 .

[19]  Sven Werner,et al.  Achieving low return temperatures from district heating substations , 2014 .

[20]  Weilong Wang,et al.  Mobilized Thermal Energy Storage for Heat Recovery for Distributed Heating , 2010 .

[21]  Luisa F. Cabeza,et al.  Thermal Energy Storage Implementation Using Phase Change Materials for Solar Cooling and Refrigeration Applications , 2012 .

[22]  Zhengguo Zhang,et al.  Preparation and thermal energy storage properties of d-Mannitol/expanded graphite composite phase change material , 2016 .

[24]  J. Rollinger,et al.  Energy/temperature diagram and compression behavior of the polymorphs of D-mannitol. , 2000, Journal of pharmaceutical sciences.

[25]  Soo-Jin Park,et al.  Thermal characterization of erythritol/expanded graphite composites for high thermal storage capacity , 2014 .

[26]  Bernd Möller,et al.  Heat Roadmap Europe: Combining district heating with heat savings to decarbonise the EU energy system , 2014 .

[27]  Rainer Scholz,et al.  Economic Efficiency of Mobile Latent Heat Storages , 2014 .

[28]  Luisa F. Cabeza,et al.  Thermal performance of sodium acetate trihydrate thickened with different materials as phase change energy storage material , 2003 .

[29]  A. Bejan,et al.  Thermal Energy Storage: Systems and Applications , 2002 .

[30]  Sven Werner,et al.  Profitability of sparse district heating , 2008 .

[31]  Ala Hasan,et al.  A combined low temperature water heating system consisting of radiators and floor heating , 2009 .

[32]  D. Li,et al.  Hotel heat pump hot water systems: impact assessment and analytic hierarchy process , 2013 .

[33]  Hironao Oguraa,et al.  Energy Recycling System Using Chemical Heat Pump Container , 2012 .

[34]  Christ Glorieux,et al.  Tuning of thermal properties of sodium acetate trihydrate by blending with polymer and silver nanoparticles , 2014 .

[35]  Qibin Liu,et al.  Evaluation and comparison of erythritol-based composites with addition of expanded graphite and carbon nanotubes , 2017 .

[36]  R. Bayón,et al.  Stability of D-mannitol upon Melting/Freezing Cycles under Controlled Inert Atmosphere , 2016 .

[37]  Soo-Jin Park,et al.  Thermal property and latent heat energy storage behavior of sodium acetate trihydrate composites containing expanded graphite and carboxymethyl cellulose for phase change materials , 2015 .

[38]  Xun Li,et al.  Numerical simulation study on optimizing charging process of the direct contact mobilized thermal energy storage , 2013 .

[39]  Luisa F. Cabeza,et al.  Thermophysical characterization and thermal cycling stability of two TCM: CaCl2 and zeolite ☆ , 2015 .

[40]  Sv Silvia Nedea,et al.  Experimental and in silico characterization of xylitol as seasonal heat storage material , 2017 .

[41]  Takahiro Nomura,et al.  Performance analysis of heat storage of direct-contact heat exchanger with phase-change material , 2013 .

[42]  A. Campos-Celador,et al.  Eutectic mixtures of sugar alcohols for thermal energy storage in the 50–90 °C temperature range , 2015 .

[43]  H. Ogura,et al.  Reaction control of CaSO4 during hydration/dehydration repetition for chemical heat pump system , 2014 .

[44]  Lianyun Wang,et al.  A zeolite 13X/magnesium sulfate–water sorption thermal energy storage device for domestic heating , 2018, Energy Conversion and Management.

[45]  Qilin Guo,et al.  Preparation and thermal properties of short carbon fibers/erythritol phase change materials , 2017 .

[46]  G. Rosengarten,et al.  D-mannitol for medium temperature thermal energy storage , 2018 .

[47]  L. Cabeza,et al.  Selection of materials with potential in sensible thermal energy storage , 2010 .

[48]  Yuan Zhou,et al.  The preparation, characterization and modification of a new phase change material: CaCl2·6H2O–MgCl2·6H2O eutectic hydrate salt , 2014 .

[49]  Javier Rodríguez-Aseguinolaza,et al.  Preparation of erythritol–graphite foam phase change composite with enhanced thermal conductivity for thermal energy storage applications , 2015 .

[50]  Wasim Saman,et al.  Computer simulation with TRNSYS for a mobile refrigeration system incorporating a phase change thermal storage unit , 2014 .

[51]  İ. Kıpçak,et al.  Magnesium recovery from magnesite tailings by acid leaching and production of magnesium chloride hexahydrate from leaching solution by evaporation , 2009 .

[52]  Erik Dahlquist,et al.  Economic assessment of the mobilized thermal energy storage (M-TES) system for distributed heat supply , 2013 .

[53]  T. Akiyama,et al.  Improvement in thermal endurance of D-mannitol as phase-change material by impregnation into nanosized pores , 2014 .

[54]  Masayoshi Yabe,et al.  Relaxation of Supercooling of Erythritol for Latent Heat Storage , 2001 .

[55]  Shaopeng Guo,et al.  Experimental study on solving the blocking for the direct contact mobilized thermal energy storage container , 2015 .

[56]  Martin Belusko,et al.  Review on transportable phase change material in thermal energy storage systems , 2017 .

[57]  F. Johnsson,et al.  Thermal energy storage in district heating: Centralised storage vs. storage in thermal inertia of buildings , 2018 .

[58]  Viviana Cocco Mariani,et al.  Economic optimization design for shell-and-tube heat exchangers by a Tsallis differential evolution , 2017 .

[59]  Jun Zhao,et al.  Techno-economic assessment of mobilized thermal energy storage for distributed users: A case study in China , 2017 .

[60]  Quantum states of neutron in Earth’s gravitional field: A challenge from the 36th international physics olympaid , 2006 .

[61]  R. C. Hartwell,et al.  Mannitol, intracranial pressure, and vasogenic edema. , 1993, Neurosurgery.

[62]  Takahiro Nomura,et al.  Thermal conductivity enhancement of erythritol as PCM by using graphite and nickel particles , 2013 .

[63]  P. Kauranen,et al.  The effect of additives on the speed of the crystallization front of xylitol with various degrees of supercooling , 2010 .

[64]  Hailong Li,et al.  Experimental study on the direct/indirect contact energy storage container in mobilized thermal energy system (M-TES) , 2014 .

[65]  J. Zeng,et al.  Effects of some nucleating agents on the supercooling of erythritol to be applied as phase change material , 2017, Journal of Thermal Analysis and Calorimetry.

[66]  W. Berndt,et al.  Erythritol: an interpretive summary of biochemical, metabolic, toxicological and clinical data. , 1998, Food and chemical toxicology : an international journal published for the British Industrial Biological Research Association.

[67]  Takahiro Nomura,et al.  Waste heat transportation system, using phase change material (PCM) from steelworks to chemical plant , 2010 .

[68]  T. Akiyama,et al.  Heat release performance of direct-contact heat exchanger with erythritol as phase change material , 2013 .

[69]  Li Shi,et al.  A eutectic mixture of galactitol and mannitol as a phase change material for latent heat storage , 2015 .

[70]  Simon Furbo,et al.  Long term thermal energy storage with stable supercooled sodium acetate trihydrate , 2015 .

[71]  Jinyue Yan,et al.  A combined experimental and simulation study on charging process of Erythritol–HTO direct-blending based energy storage system , 2014 .

[72]  D. Blumberga,et al.  Pathway and restriction in district heating systems development towards 4th generation district heating , 2018, Energy.

[73]  K. Nagano,et al.  Thermal characteristics of magnesium nitrate hexahydrate and magnesium chloride hexahydrate mixture as a phase change material for effective utilization of urban waste heat , 2004 .

[74]  T. Akiyama,et al.  Thermophysical and heat transfer properties of phase change material candidate for waste heat transportation system , 2008 .

[75]  A. Sharma,et al.  Review on thermal energy storage with phase change materials and applications , 2009 .

[76]  Simon Furbo,et al.  Thermo-economic optimization of a hybrid solar district heating plant with flat plate collectors and parabolic trough collectors in series , 2018, Energy Conversion and Management.

[77]  H. Daiguji,et al.  Crystallization and Melting Behavior of Erythritol In and Around Two-Dimensional Hexagonal Mesoporous Silica , 2015 .

[78]  A. Artru,et al.  Mannitol, intracranial pressure and vasogenic edema. , 1995, Neurosurgery.

[79]  Dagnija Blumberga,et al.  The future competitiveness of the non-Emissions Trading Scheme district heating systems in the Baltic States , 2016 .

[80]  D. Buddhi,et al.  Thermal cycling test of few selected inorganic and organic phase change materials , 2008 .

[81]  S. D. Sharma,et al.  Thermal performance of a solar cooker based on an evacuated tube solar collector with a PCM storage unit , 2005 .

[82]  Jinyue Yan,et al.  Mobilized Thermal Energy Storage (M‐TES) Technology for Industry Heat Recovery , 2015 .

[83]  Khamid Mahkamov,et al.  Solar energy storage using phase change materials , 2007 .

[84]  Changying Zhao,et al.  First-principle study of CaO/Ca(OH)2 thermochemical energy storage system by Li or Mg cation doping , 2014 .

[85]  Jinyue Yan,et al.  Thermal performance of a shell-and-tube latent heat thermal energy storage unit : Role of annular fins , 2017 .

[86]  Luisa F. Cabeza,et al.  Thermal energy storage (TES) for industrial waste heat (IWH) recovery: A review , 2016 .

[87]  Yi Wang,et al.  Supercooling suppression and thermal behavior improvement of erythritol as phase change material for thermal energy storage , 2017 .

[88]  Byung Chul Shin,et al.  Prevention of supercooling and stabilization of inorganic salt hydrates as latent heat storage materials , 1992 .

[89]  Peng Hu,et al.  Phase change performance of sodium acetate trihydrate with AlN nanoparticles and CMC , 2011 .

[90]  Anibal T. de Almeida,et al.  Ground source heat pump carbon emissions and primary energy reduction potential for heating in buildings in Europe—results of a case study in Portugal , 2015 .

[91]  T. Akiyama,et al.  Heat storage in direct-contact heat exchanger with phase change material , 2013 .

[92]  Ibrahim Dincer,et al.  Performance analyses of sensible heat storage systems for thermal applications , 1997 .