Thermo-chemical wear model and worn tool shapes for single-crystal diamond tools cutting steel
暂无分享,去创建一个
[1] D. Crompton,et al. The wear of diamond , 1973, Proceedings of the Royal Society of London. A. Mathematical and Physical Sciences.
[2] Paul Mativenga,et al. Heat generation and temperature prediction in metal cutting: A review and implications for high speed machining , 2006 .
[3] C. Arcona,et al. An Empirical Tool Force Model for Precision Machining , 1998 .
[4] Satoshi Kiyono,et al. Nanometer edge profile measurement of diamond cutting tools by atomic force microscope with optical alignment sensor , 2006 .
[5] Tao Sun,et al. Design criterion for crystal orientation of diamond cutting tool , 2009 .
[6] H. Yoshioka,et al. In-process microsensor for ultraprecision machining , 2004 .
[7] Toshimichi Moriwaki,et al. Combined Stress, Material Flow and Heat Analysis of Orthogonal Micromachining of Copper , 1993 .
[8] Takashi Ueda,et al. The Temperature of a Single Crystal Diamond Tool in Turning , 1998 .
[9] Akira Kobayashi,et al. Measuring the Very Small Cutting-Edge Radius for a Diamond Tool Using a New Kind of SEM Having Two Detectors , 1990 .
[10] Kui Liu,et al. Nano-precision measurement of diamond tool edge radius for wafer fabrication , 2003 .
[11] Thomas A. Dow,et al. Diamond tool wear measurement by electron-beam-induced deposition , 2010 .
[12] Tao Sun,et al. Finite element optimization of diamond tool geometry and cutting-process parameters based on surface residual stresses , 2007 .
[13] R. Komanduri,et al. Thermal modeling of the metal cutting process — Part III: temperature rise distribution due to the combined effects of shear plane heat source and the tool–chip interface frictional heat source , 2001 .
[14] J. Wilks,et al. Tool wear and solid state reactions during machining , 1979 .
[15] J. Drescher. Scanning electron microscopic technique for imaging a diamond tool edge , 1993 .
[16] J. Wilks,et al. The wear of diamond tools turning mild steel , 1980 .
[17] Yingxue Yao,et al. The Optimum Crystal Plane of Natural Diamond Tool for Precision Machining , 1992 .
[18] John S. Strenkowski,et al. Finite element models of orthogonal cutting with application to single point diamond turning , 1988 .
[19] F. Fang,et al. Investigations of tool edge radius effect in micromachining : A FEM simulation approach , 2008 .
[20] J. Wilks,et al. The resistance of diamond to abrasion , 1959 .
[21] H. Takeyama,et al. Basic Investigation of Tool Wear , 1963 .
[22] Ranga Komanduri,et al. Thermal modeling of the metal cutting process: Part I — Temperature rise distribution due to shear plane heat source , 2000 .
[23] R. Komanduri,et al. Thermal modeling of the metal cutting process — Part II: temperature rise distribution due to frictional heat source at the tool–chip interface , 2001 .
[24] Howard W. Yoon,et al. Simultaneous visible and thermal imaging of metals during machining , 2005, SPIE Defense + Commercial Sensing.
[25] Masahiro Higuchi,et al. Thermo-Chemical Wear Mechanism of Diamond Tool in Machining of Ferrous Metals , 2004 .
[26] Eiji Shamoto,et al. Ultraprecision diamond turning of stainless steel by applying ultrasonic vibration , 1991 .
[27] C. Evans,et al. Cryogenic Diamond Turning of Stainless Steel , 1991 .
[28] Chi Fai Cheung,et al. Computer simulation of single-point diamond turning using finite element method , 2005 .
[29] Christopher J. Evans,et al. Chemical aspects of tool wear in single point diamond turning , 1996 .
[30] Don A. Lucca,et al. Effect of Tool Edge Geometry on Energy Dissipation in Ultraprecision Machining , 1993 .
[31] J. M. Casstevens,et al. Diamond turning of steel in carbon-saturated atmospheres , 1983 .
[32] R. Komanduri,et al. On the diffusion wear of diamond in grinding pure iron , 1976 .
[33] J. Archard,et al. The wear of metals under unlubricated conditions , 1956, Proceedings of the Royal Society of London. Series A. Mathematical and Physical Sciences.
[34] Thomas A. Dow,et al. Diamond tool wear when machining Al6061 and 1215 steel , 2010 .
[35] T. Kitagawa,et al. Analytical prediction of cutting tool wear , 1984 .
[36] J. Jiang,et al. The effect of sliding speed on wear of diamond-like carbon coatings , 1998 .
[37] A. Molinari,et al. Modeling of tool wear by diffusion in metal cutting , 2002 .
[38] J. F. Archard,et al. The temperature of rubbing surfaces , 1959 .
[39] Ekkard Brinksmeier,et al. Advances in Precision Machining of Steel , 2001 .