Progress in the fabrication of high-aspect-ratio zone plates by soft x-ray lithography

Fabrication of Fresnel zone plates for the hard x-ray spectral region combines the challenge of high lateral resolution (~100 nm) with a large thickness requirement for the phase-shifting material (0.5-3 μm). For achieving a high resolution, the initial mask was fabricated by e-beam lithography and gold electroforming. To prevent the collapse of the structures between the developing and electroforming processes, drying was completely eliminated. Fabrication errors, such as nonuniform gold electroplating and collapse of structures, were analyzed and systematically eliminated. We optimized the exposure and developing processes for 950k and 2200k polymethylmethacrylate of different thicknesses and various adhesion promoters. We discuss the effects of these fabrication steps on the zone plate's resolution and aspect ratio. Fresnel zone plates with 110 nm outermost zone width, 150 μm diameter, and 1.3 μm gold thickness were fabricated. Preliminary evaluation of the FZPs was done by scanning electron microscopy and atomic force microscopy. The FZP focusing performance was characterized at the Advanced Photon Source at Argonne National Laboratory.

[1]  Erik H. Anderson,et al.  Electron beam lithography digital pattern generator and electronics for generalized curvilinear structures , 1995 .

[2]  B. Niemann,et al.  Soft X-ray imaging zone plates with large zone numbers for microscopic and spectroscopic applications , 1974 .

[3]  Janos Kirz,et al.  Phase zone plates for x rays and the extreme uv , 1974 .

[4]  Erik H. Anderson,et al.  Nanofabrication and diffractive optics for high-resolution x-ray applications , 2000 .

[5]  Chris Jacobsen,et al.  Process optimization for production of sub-20 nm soft x-ray zone plates , 1997 .

[6]  Denice D. Denton,et al.  Hard x‐ray phase zone plate fabricated by lithographic techniques , 1992 .

[7]  Volker Schlott,et al.  Diffractive lenses for photon energies ranging from the extreme ultraviolet to hard x rays , 2001, SPIE Optics + Photonics.

[8]  Volker Saile,et al.  PMMA as an X-ray resist for micro-machining application: latent image formation and thickness losses , 1996 .

[9]  Jian Wang,et al.  Fabrication of circular optical structures with a 20 nm minimum feature size using nanoimprint lithography , 2000 .

[10]  Jean Susini,et al.  High-resolution lenses for sub-100 nm x-ray fluorescence microscopy , 2000 .

[11]  Christian David,et al.  Low‐distortion electron‐beam lithography for fabrication of high‐resolution germanium and tantalum zone plates , 1995 .

[12]  Jean Susini,et al.  Electroplated gold zone plates as X-ray objectives for photon energies of 2–8 keV , 2000 .

[13]  B. Lai,et al.  Nanometer focusing of hard x rays by phase zone plates , 1999 .

[14]  Hiroaki Oizumi,et al.  X-Ray Lithography with a Wet-Silylated and Dry-Developed Resist , 1995 .

[15]  Hiroaki Oizumi,et al.  Prevention of Resist Pattern Collapse by Flood Exposure during Rinse Process , 1994 .

[16]  Zheng Chen,et al.  0.1-μm high-aspect-ratio pattern replication and linewidth control , 1998, Advanced Lithography.

[17]  M. Peuker,et al.  High-efficiency nickel phase zone plates with 20 nm minimum outermost zone width , 2001 .

[18]  G. M. Wells,et al.  X-ray lithography beamlines at Aladdin , 1988 .

[19]  Enzo Di Fabrizio,et al.  Toward high resolution and high efficiency Zone Plate for X-ray applications , 2000 .