Fabrication of micro end mills by wire EDM and some micro cutting tests

Extremely fine end mills with noncircular cross-sectional profiles have been fabricated utilizing wire electro discharge machining. By using suitable electro discharging conditions, the geometrical error of the end mill and the roundness of the cutting edge were both controlled below 1 µm. Micro grooving tests were performed on electroless nickel plating using these end mills, and the machining behavior was investigated. Nearly burr-free precision machining was realized. Until a total cutting distance of 1000 mm, no remarkable change was found in the cutting force and chip formation, demonstrating the high anti-wear ability of the tools. It can be presumed that the electro discharge-induced micro asperities on the tool surface play an important role in machining by improving the tribological properties of the tool–workpiece interface.

[1]  Tsunemoto Kuriyagawa,et al.  Precision machining of microstructures on electroless-plated NiP surface for molding glass components , 2009 .

[2]  B. Yan,et al.  Fabrication of a micro-spherical tool in EDM combined with Ni-diamond co-deposition , 2008 .

[3]  Chengfeng Li,et al.  Modelling and experimental analysis of the effects of tool wear, minimum chip thickness and micro tool geometry on the surface roughness in micro-end-milling , 2008 .

[4]  Tae Jo Ko,et al.  Micro-end-milling of single-crystal silicon , 2007 .

[5]  O. B. Ozdoganlar,et al.  An experimental investigation of micro-machinability of copper 101 using tungsten carbide micro-endmills , 2007 .

[6]  Gwo-Lianq Chern,et al.  Study on burr formation in micro-machining using micro-tools fabricated by micro-EDM , 2007 .

[7]  Gwo-Lianq Chern,et al.  Experimental observation and analysis of burr formation mechanisms in face milling of aluminum alloys , 2006 .

[8]  Makoto Miyazaki,et al.  Electrical discharge machining with ultralow discharge energy , 2006 .

[9]  Eckart Uhlmann,et al.  Micro milling of sintered tungsten–copper composite materials , 2005 .

[10]  E. Uhlmann,et al.  Machining of micro/miniature dies and moulds by electrical discharge machining—Recent development , 2005 .

[11]  J. Schmidt,et al.  New applications for micro-EDM , 2004 .

[12]  A. Kubo,et al.  Chip Formation Behaviour in Ultra-Precision Cutting of Electroless Nickel Plated Mold Substrates , 2004 .

[13]  David Dornfeld,et al.  Micro-Burr Formation and Minimization through Process Control , 2003 .

[14]  A. Kumar,et al.  Micro milling of pure copper , 2001 .

[15]  G. L. Benavides,et al.  Micromilling of metal alloys with focused ion beam–fabricated tools , 1999 .

[16]  Lothar Bohn,et al.  Microstructure grooves with a width of less than 50 μm cut with ground hard metal micro end mills , 1999 .

[17]  Tsunemoto Kuriyagawa,et al.  Study on shaping spherical Poly Crystalline Diamond tool by Micro-electro-Discharge Machining and micro-grinding with the tool , 2007 .

[18]  Naoto Ohtake,et al.  Development of a Cutting Tool with Micro Structured Surface , 2007 .

[19]  Kazuhiko Kudo,et al.  Development of Global Optimization Method by Orthogonal Array (Application to Turbine Stage Design) , 2007 .

[20]  David Dornfeld,et al.  Drilling Burr Formation in Titanium Alloy, Ti-6AI-4V , 1999 .

[21]  Takahisa Masuzawa,et al.  Wire Electro-Discharge Grinding for Micro-Machining , 1985 .