Application of genetic algorithms in design and optimisation of multi-stream plate–fin heat exchangers

This paper introduces two new approaches in the thermo-hydraulic design of multi-stream heat exchangers (MSHEs). In both approaches, geometrical aspects of the MSHE (e.g. exchanger dimensions, fin type, etc.) are optimised with a genetic algorithm (GA) using the Total Annual Cost (TAC) as an objective function. The first approach is capable of utilising the maximum allowable stream pressure drops and can result in minimal surface area requirements. In the second approach, all of the pressure drop values are considered as design variables and are therefore subject to optimisation. These approaches have been applied to two case studies taken from literature, and the results are compared to those arising from a currently used design method. In the first case study, application of the new approaches resulted in a smaller TAC than the current approach by 5.77% and 31.86%, respectively, and improvement in the second case was estimated to be 5% and 21.46%, correspondingly. The effect of different fins on an MSHE's TAC is discussed through application of GAs to the current approach. It is shown that correct selection of fin types reduces the TAC of the two case studies by 21.75% and 8.7%, respectively. © 2012 Canadian Society for Chemical Engineering

[1]  Xiang Ling,et al.  Optimal design approach for the plate-fin heat exchangers using neural networks cooperated with genetic algorithms , 2008 .

[2]  Melanie Mitchell,et al.  An introduction to genetic algorithms , 1996 .

[3]  Xing Luo,et al.  Thermal design of multi-fluid mixed-mixed cross-flow heat exchangers , 2010 .

[4]  Ramin Bozorgmehry Boozarjomehry,et al.  Which method is better for the kinetic modeling: Decimal encoded or Binary Genetic Algorithm? , 2007 .

[5]  Lieke Wang, Bengt Sundén.  Design Methodology for Multistream Plate-Fin Heat Exchangers in Heat Exchanger Networks , 2001 .

[6]  Majid Amidpour,et al.  Application of process decomposition in multi-stream plate fin heat exchangers design to use in heat recovery networks , 2007 .

[7]  Louis Gosselin,et al.  Review of utilization of genetic algorithms in heat transfer problems , 2009 .

[8]  G. T. Polley,et al.  Thermal design of multi-stream heat exchangers , 2002 .

[9]  B. S. V. Prasad,et al.  The sizing and passage arrangement of multistream plate-fin heat exchangers , 1996 .

[10]  Dilip Kumar Pratihar,et al.  Optimum stacking pattern for multi-stream plate-fin heat exchanger through a genetic algorithm , 2011 .

[11]  Martín Picón-Núñez,et al.  Flow Passage Arrangement and Surface Selection in Multistream Plate-Fin Heat Exchangers , 2005 .

[12]  Sunil Sarangi,et al.  Second law based optimisation of crossflow plate-fin heat exchanger design using genetic algorithm , 2009 .

[13]  Goldberg,et al.  Genetic algorithms , 1993, Robust Control Systems with Genetic Algorithms.

[14]  Ignacio E. Grossmann,et al.  Simultaneous optimization models for heat integration—I. Area and energy targeting and modeling of multi-stream exchangers , 1990 .

[15]  John J. Grefenstette,et al.  Optimization of Control Parameters for Genetic Algorithms , 1986, IEEE Transactions on Systems, Man, and Cybernetics.

[16]  Pingjing Yao,et al.  Synthesis of multi-stream heat exchanger network for multi-period operation with genetic/simulated annealing algorithms , 2008 .

[17]  Qiuwang Wang,et al.  Application of a Genetic Algorithm for Thermal Design of Fin-and-Tube Heat Exchangers , 2008 .

[18]  N. Niclout,et al.  MINLP optimization of plate fin heat exchangers , 2003 .

[19]  Ignacio E. Grossmann,et al.  Simultaneous optimization models for heat integration. III, Process and heat exchanger network optimization , 1990 .

[20]  Pooya Hoseinpoori,et al.  Energy and cost optimization of a plate and fin heat exchanger using genetic algorithm , 2011 .