Dimensional metrology with X-ray CT: A comparison with CMM measurements on internal features and compliant structures

Abstract X-ray computed tomography (CT) is uniquely suited for dimensional measurement of components having internal geometry, difficult-to-reach part features, and easy-to-deform or flexible structures. Through the development of standards it is also becoming accepted as a metrology tool. The objectives of this study are to compare dimensional measurements on artifacts containing internal structures and mechanically compliant features using current state-of-the-art CT and coordinate measure machine (CMM) techniques. It also aims to discuss some of the issues with recently developed standards for CT measurement uncertainty estimation. To illustrate the challenges of CMM and the potential of X-ray CT for reliable dimensional inspection, two different problems are presented: 1) characterization of internal geometry in a metallic artifact that has features inaccessible to tactile or vision-based measurement techniques; and 2) evaluation of dimensional measurement of diameters, form, and relative distances in the components of a flexible object with stems that bend due to mechanical contact by tactile instruments, e.g., CMM. In addition, some issues with the direct application of the ISO 15530 series for the estimation of CT measurement uncertainties are discussed, and a generalized formalism for uncertainty budgeting in CT metrology (still based on the ISO 15530 guidelines but with some differences) is applied to the measurements presented throughout this paper. For dimensions of geometric features ranging from 0.6 mm to 65 mm, a comparison between CT and CMM measurements typically resulted in differences of approximately 5 μm or less for most of the measurements, while expanded uncertainties computed for the CT measurements ranged from 1 to 20 μm. CT measurements on the internal geometries resulted in uncertainties comparable to CMM data that were obtained with the metallic artifact disassembled. However, in the particular case of measuring compliant structures, the conventional CMM strategies led to large systematic errors in the measurements. It is demonstrated that using extrapolation methods, measurements from these two systems converged to within ± 2 μm.

[1]  Leonardo De Chiffre,et al.  InteraqCT Comparison on Assemblies - Final Report , 2016 .

[2]  Pawel J. Swornowski,et al.  A critical look at the coordinate measuring technique , 2013 .

[3]  Luca Mari,et al.  Quantity and quantity value , 2012 .

[4]  Jochen Hiller,et al.  Computed Tomography as a Tool for Tolerance Verification of Industrial Parts , 2013 .

[5]  Eduard Gröller,et al.  Fuzzy CT Metrology: Dimensional Measurements on Uncertain Data , 2013, SCCG.

[6]  Enrico Savio,et al.  Influence of surface roughness on computed tomography dimensional measurements , 2017 .

[7]  Avinash C. Kak,et al.  Principles of computerized tomographic imaging , 2001, Classics in applied mathematics.

[8]  Dimitris Mihailidis,et al.  Computed Tomography: From Photon Statistics to Modern Cone-Beam CT , 2008 .

[9]  Robert Schmitt,et al.  Computed tomography for dimensional metrology , 2011 .

[10]  Graham T. Smith,et al.  Machine Tool Metrology: An Industrial Handbook , 2016 .

[11]  Ignacio Lira,et al.  The evaluation of the uncertainty in knowing a directly measured quantity , 1998 .

[12]  Hamid M. Lankarani,et al.  Compliant contact force models in multibody dynamics : evolution of the Hertz contact theory , 2012 .

[13]  Walter Bich,et al.  From Errors to Probability Density Functions. Evolution of the Concept of Measurement Uncertainty , 2012, IEEE Transactions on Instrumentation and Measurement.

[14]  Jochen Hiller,et al.  Physical characterization and performance evaluation of an x-ray micro-computed tomography system for dimensional metrology applications , 2012 .

[15]  Frank Härtig,et al.  Current state of standardization in the field of dimensional computed tomography , 2014 .

[16]  Robert N. Yancey,et al.  X-Ray Computed Tomography Application Research , 1996 .

[17]  P. Aldebert,et al.  α Al2O3: A high-temperature thermal expansion standard , 1984 .

[18]  Ignacio Lira,et al.  DESIGN NOTE: Evaluation of the uncertainty associated with a measurement result not corrected for systematic effects , 1998 .

[19]  Ignacio Lira,et al.  Evaluating the Measurement Uncertainty , 2002 .

[20]  Georgia L. Harris,et al.  Proficiency Testing Program for U.S. State Weights and Measures Laboratories , 2012 .

[21]  S. Carmignato,et al.  Accuracy of industrial computed tomography measurements: Experimental results from an international comparison , 2012 .

[22]  Jochen Hiller,et al.  Measurement accuracy in X-ray computed tomography metrology: Toward a systematic analysis of interference effects in tomographic imaging , 2016 .

[23]  Robert Hooke,et al.  Uncertainty, Calibration and Probability. , 1974 .

[24]  Marek Dobosz,et al.  Metrological feasibilities of CMM touch trigger probes. Part I: 3D theoretical model of probe pretravel , 2003 .

[25]  A. Kung,et al.  AFM investigation on surface damage caused by mechanical probing with small ruby spheres , 2007 .

[26]  Markus Bartscher,et al.  Obtaining dimensional information by industrial CT scanning - present and prospective process chain , 2003 .

[27]  R. Thalmann,et al.  Novel 3D analogue probe with a small sphere and low measurement force , 2003 .

[28]  Michael Krystek,et al.  The 2016 Revision of ISO 1 - Standard Reference Temperature for the Specification of Geometrical and Dimensional Properties. , 2016, Journal of research of the National Institute of Standards and Technology.

[29]  Jörg Hoffmann,et al.  Probing Systems for Coordinate Measuring Machines , 2011 .

[30]  Steven D. Phillips,et al.  Guidelines for Expressing the Uncertainty of Measurement Results Containing Uncorrected Bias , 1997, Journal of research of the National Institute of Standards and Technology.

[31]  Herminso Villarraga-Gomez.  X-ray Computed Tomography for Dimensional Measurements , 2016 .

[32]  Wenjuan Sun,et al.  An overview of industrial X-ray computed tomography. , 2012 .

[33]  Luca Mari,et al.  Measurement, Models, and Uncertainty , 2012, IEEE Transactions on Instrumentation and Measurement.

[34]  Peter J. Shull,et al.  X-Ray Imaging: Fundamentals, Industrial Techniques and Applications , 2016 .

[35]  Daniel Kleppner,et al.  An introduction to mechanics , 2010 .

[36]  Guido Tosello,et al.  A 3D edge detection technique for surface extraction in computed tomography for dimensional metrology applications , 2013 .

[37]  Robert Schmitt,et al.  Industrial applications of computed tomography , 2014 .

[38]  John R. Stoup,et al.  Measurements of large silicon spheres using the NIST M48 coordinate measuring machine , 2003, SPIE Optics + Photonics.

[39]  Leonardo De Chiffre,et al.  Inter laboratory comparison on Industrial Computed Tomography: CIA-CT comparison. Final Report , 2013 .

[40]  Ted Doiron,et al.  20 °C—A Short History of the Standard Reference Temperature for Industrial Dimensional Measurements , 2007, Journal of research of the National Institute of Standards and Technology.

[41]  R. Thalmann,et al.  Ultraprecision micro-CMM using a low force 3D touch probe , 2007 .

[42]  G. Hermann.  Error Correction in 3D Coordinate Measurement , 2006, 2006 International Conference on Intelligent Engineering Systems.

[43]  S. Standard.  GUIDE TO THE EXPRESSION OF UNCERTAINTY IN MEASUREMENT , 2006 .

[44]  Fabien Grégis,et al.  The evaluation of measurement uncertainties and its epistemological ramifications. , 2017, Studies in history and philosophy of science.

[45]  Bernd Balle.  Measuring means knowledge , 2017 .

[46]  Richard H. Bossi,et al.  X-Ray Computed Tomographic Inspection of Castings , 1991 .

[47]  L. De Chiffre,et al.  Interlaboratory comparison of a physical and a virtual assembly measured by CT , 2018 .

[48]  Luca Mari,et al.  Epistemology of measurement , 2003 .

[49]  S. V. Gupta.  Measurement Uncertainties: Physical Parameters and Calibration of Instruments , 2012 .

[50]  A G Steele,et al.  Extending En for measurement science , 2006 .

[51]  Jerzy A. Sladek,et al.  Coordinate Metrology: Accuracy of Systems and Measurements , 2015 .

[52]  R. Bracewell.  Fourier Analysis and Imaging , 2004 .

[53]  Jean-Pierre Kruth,et al.  Uncertainty Determination for Dimensional Measurements with Computed Tomography , 2012 .

[54]  Luca Mari,et al.  The problem of foundations of measurement , 2005 .

[55]  Luca Mari,et al.  Quantities, quantification, and the necessary and sufficient conditions for measurement , 2017 .

[56]  F. Pavese.  ON THE DIFFERENCE OF MEANINGS OF "ZERO CORRECTION": ZERO VALUE versus NO CORRECTION, AND OF THE ASSOCIATED UNCERTAINTIES , 2012 .

[57]  D. A. Swyt.  Length and Dimensional Measurements at NIST , 2001, Journal of research of the National Institute of Standards and Technology.

[58]  L. Kirkup,et al.  An Introduction to Uncertainty in Measurement: Introduction to uncertainty in measurement , 2006 .

[59]  Jochen Hiller,et al.  A study on evaluation strategies in dimensional X-ray computed tomography by estimation of measurement uncertainties , 2012 .

[60]  Richard H. Bossi,et al.  X-Ray CT for Quantitative Casting Material Evaluation , 1994 .

[61]  Robert N. Yancey,et al.  DIMENSIONAL MEASUREMENT OF INTERNAL FEATURES IN COMPLEX CASTINGS , 1995 .

[62]  Theodore D. Doiron,et al.  Accuracy and versatility of the NIST M48 coordinate measuring machine , 2001, Lasers in Metrology and Art Conservation.

[63]  Bertil Magnusson,et al.  Treatment of uncorrected measurement bias in uncertainty estimation for chemical measurements , 2008, Analytical and bioanalytical chemistry.

[64]  Wim Dewulf,et al.  Uncertainty determination and quantification for dimensional measurements with industrial computed tomography , 2013 .

[65]  Simone Carmignato,et al.  Influence of surface roughness on X-ray computed tomography dimensional measurements of additive manufactured parts , 2016 .

[66]  Frank Natterer,et al.  Mathematical methods in image reconstruction , 2001, SIAM monographs on mathematical modeling and computation.

[67]  Wim Dewulf,et al.  Industrial computer tomography for dimensional metrology: Overview of influence factors and improvement strategies , 2009 .

[68]  Jochen Hiller,et al.  Measurement uncertainty evaluation in dimensional X-ray computed tomography using the bootstrap method , 2014 .

[69]  D. A. Swyt.  Uncertainties in Dimensional Measurements Made at Nonstandard Temperatures , 1994, Journal of research of the National Institute of Standards and Technology.

[70]  Ozden O. Ochoa,et al.  Transverse and Longitudinal CTE Measurements of Carbon Fibers and their Impact on Interfacial Residual Stresses in Composites , 2006 .

[71]  S. Deans.  The Radon Transform and Some of Its Applications , 1983 .

[72]  A. Weckenmann,et al.  Probing Systems in Dimensional Metrology , 2004 .

[73]  Jochen Hiller,et al.  Estimation of measurement uncertainties in X-ray computed tomography metrology using the substitution method , 2014 .

[74]  Christof Reinhart,et al.  INDUSTRIAL COMPUTER TOMOGRAPHY - A UNIVERSAL INSPECTION TOOL , 2008 .

[75]  Luca Mari,et al.  Modelling Measurement: Error and Uncertainty , 2014 .

[76]  E.J.C. Bos,et al.  Aspects of tactile probing on the micro scale , 2011 .

[77]  Robert Schmitt,et al.  Uncertainty in measurement for x-ray-computed tomography using calibrated work pieces , 2010 .

[78]  Markus Bartscher,et al.  ISO test survey on material influence in dimensional computed tomography , 2016 .

[79]  Erik L. Ritman,et al.  Past and future directions in x‐ray computed tomography (CT) , 2002, Int. J. Imaging Syst. Technol..

[80]  Roosevelt Gibson,et al.  Dimensional Accuracy in X-Ray Computed Tomography Imaging , 1998 .

[81]  Guido Tosello,et al.  Experimental Approach for the Uncertainty Assessment of 3D Complex Geometry Dimensional Measurements Using Computed Tomography at the mm and Sub-mm Scales , 2017, Sensors.

[82]  L. De Chiffre,et al.  Comparison on Computed Tomography using industrial items , 2014 .

[83]  Jochen Hiller,et al.  A computer simulation platform for the estimation of measurement uncertainties in dimensional X-ray computed tomography , 2012 .