Polyethylene/sepiolite fibers. Influence of drawing and nanofiller content on the crystal morphology and mechanical properties

The influence of sepiolite content (1, 2, and 3 wt%) and successive drawing steps on the final properties of polyethylene/sepiolite nanocomposite fibers are reported. Particularly the effects of these variables on crystallinity, fiber macroscopic morphology, and tensile mechanical properties are analyzed applying different experimental techniques: differential scanning calorimetry, wide angle x-ray diffraction, scanning electronic microscopy, and tensile mechanical characterization. The study evidenced the important role of both sepiolite content and stretching on the crystalline morphology and mechanical properties of the nanocomposites fiber. Both variables favor the appearance of the monoclinic phase during polyethylene crystallization, and produce an increase of crystallinity degree (35 % with drawing steps and 10 % by the sepiolite incorporation in non drawing fiber). This change of crystal morphology influences mechanical properties enhancing with both sepiolite content and drawing steps. Thus, Young Modulus increases 17 times with drawing in pure PE fibers and 1.5 times because sepiolite presence. The strength shows similar behavior, but the elongation at break decreases 14 timed with draw steps and to a half by the sepiolite influence. The final properties of drawing nanocomposite fibers are so acceptable for textile applications and they content particles that enhance their moisture and odors absorptive capacities. POLYM. ENG. SCI., 55:1096–1103, 2015. © 2014 Society of Plastics Engineers

[1]  Z. Wilchinsky.  Determination of orientation of the crystalline and amorphous phases in polyethylene by X‐ray diffraction , 1968 .

[2]  C. Macosko,et al.  Intercalated linear low density polyethylene (LLDPE)/clay nanocomposites prepared with oxidized polyethylene as a new type compatibilizer: Structural, mechanical and barrier properties , 2007 .

[3]  M. Molina-Sabio,et al.  Adsorption–desorption of water vapor by natural and heat-treated sepiolite in ambient air , 1999 .

[4]  R. Nigmatullin,et al.  Polymer-layered silicate nanocomposites in the design of antimicrobial materials , 2008 .

[5]  N. García,et al.  Comparing the effect of nanofillers as thermal stabilizers in low density polyethylene , 2009 .

[6]  L. Bokobza,et al.  Fibre reinforcement of elastomers: nanocomposites based on sepiolite and poly(hydroxyethyl acrylate) , 2004 .

[7]  C. R. Desper,et al.  Physical and mechanical properties of ultra‐oriented high‐density polyethylene fibers , 1979 .

[8]  R. Young,et al.  Deformation mechanisms in biaxially drawn polyethylene , 1991 .

[9]  Liliane Bokobza,et al.  Elastomeric composites. I. Silicone composites , 2004 .

[10]  Anuvat Sirivat,et al.  Preparation, structure, properties and thermal behavior of rigid-rod polyimide/montmorillonite nanocomposites , 2001 .

[11]  I. Ward,et al.  On the influence of initial morphology on the internal structure of highly drawn polyethylene , 2000 .

[12]  E. Galán.  Properties and Applications of Palygorskite-Sepiolite Clays , 1996, Clay Minerals.

[13]  Fosong Wang,et al.  Preparation, structure and thermomechanical properties of nylon-6 nanocomposites with lamella-type and fiber-type sepiolite , 2007 .

[14]  J. Kenny,et al.  Polyethylene‐based nanocomposite films: Structure/properties relationship , 2014 .

[15]  T. Amornsakchai,et al.  On the influence of molecular weight and crystallisation condition on the development of defect in highly drawn polyethylene , 2002 .

[16]  T. Yasin,et al.  Synthesis and characterization of linear low-density polyethylene/sepiolite nanocomposites , 2012 .

[17]  J. González‐Benito,et al.  Crystallization and final morphology of HDPE : Effect of the high energy ball milling and the presence of TiO2 nanoparticles , 2009 .

[18]  L. Mandelkern,et al.  Influence of structural and morphological factors on the mechanical properties of the polyethylenes , 1987 .

[19]  T. Amornsakchai,et al.  High strength polyethylene fibers from high density polyethylene/organoclay composites , 2007 .

[20]  P. Barham,et al.  Self‐hardening of highly oriented polyethylene , 1977 .

[21]  A. Aznar,et al.  Microfibrous Chitosan−Sepiolite Nanocomposites , 2006 .

[22]  D. Mendeleev,et al.  Nanocomposites and high-modulus fibers based on ultrahigh-molecular-weight polyethylene and silicates: Synthesis, structure, and properties , 2014, Polymer Science Series A.

[23]  R. Gudavalli,et al.  Nanoparticle effects on the crystallization of polyethylene at elevated pressures , 2008 .