Experimental Studies and Comparison of Centrifugally Cast Cu/SiC and Cu/Si3N4 Functionally Graded Composites on Mechanical and Wear Behavior

[1]  N. Radhika,et al.  Effect of reinforcement content on the adhesive wear behavior of Cu10Sn5Ni/Si3N4 composites produced by stir casting , 2017, International Journal of Minerals, Metallurgy, and Materials.

[2]  Huijun Kang,et al.  Effects of Cr and Zr additions on microstructure and properties of Cu-Ni-Si alloys , 2016 .

[3]  C. Bindal,et al.  Fabrication and properties of SiC reinforced copper-matrix-composite contact material , 2016 .

[4]  N. Radhika,et al.  Development of functionally graded aluminium composites using centrifugal casting and influence of reinforcements on mechanical and wear properties , 2016 .

[5]  R. Zamiri,et al.  Microstructural and sliding wear behavior of SiC-particle reinforced copper matrix composites fabricated by sintering and sinter-forging processes , 2016 .

[6]  N. Radhika,et al.  Mechanical and tribological properties of functionally graded aluminium/zirconia metal matrix composite synthesized by centrifugal casting , 2015 .

[7]  S. Vedantam,et al.  Layer-Graded Cu/B4C/Graphite Hybrid Composites: Processing, Characterization, and Evaluation of Their Mechanical and Wear Behavior , 2015 .

[8]  M. Eslami,et al.  Study on tribological behavior of electrodeposited Cu–Si3N4 composite coatings , 2014 .

[9]  Q. Lei,et al.  A new ultrahigh strength Cu-Ni-Si alloy , 2013 .

[10]  Amarjit Singh,et al.  ABRASIVE WEAR BEHAVIOUR OF COPPER-SiC AND COPPER-SiO2 COMPOSITES , 2013 .

[11]  N. Radhika,et al.  Effect of reinforcement on wear behaviour of aluminium hybrid composites , 2013 .

[12]  A. Jha,et al.  Microstructure and Properties of a High-Strength Cu-Ni-Si-Co-Zr Alloy , 2013, Journal of Materials Engineering and Performance.

[13]  W. Jin,et al.  Study on preparation of copper matrix composites reinforced by SiC and Graphite particles , 2012, 2012 2nd International Conference on Consumer Electronics, Communications and Networks (CECNet).

[14]  H. Assadi,et al.  Evaluation of microstructure and wear behavior of friction stir processed cast aluminum alloy , 2012 .

[15]  R. Rana,et al.  Reviews on the Influences of Alloying elements on the Microstructure and Mechanical Properties of Aluminum Alloys and Aluminum Alloy Composites , 2012 .

[16]  Ndy Ekere,et al.  Investigation of thermal management materials for automotive electronic control units , 2011 .

[17]  S. F. Moustafa,et al.  Preparation and properties of Al2O3 nanoparticle reinforced copper matrix composites by in situ processing , 2009 .

[18]  Zhi-you Li,et al.  Microstructure and properties of high-conductivity, super-high-strength Cu–8.0Ni–1.8Si–0.6Sn–0.15Mg alloy , 2009 .

[19]  Y. Waseda,et al.  Improvement in strength and electrical conductivity of Cu–Ni–Si alloys by aging and cold rolling , 2006 .

[20]  R. Lin,et al.  Wear resistance of WC particle reinforced copper matrix composites and the effect of porosity , 2006 .

[21]  Jinsong Zhang,et al.  Interfacial reactions in 3D-SiC network reinforced Cu-matrix composites prepared by squeeze casting , 2005 .

[22]  Y. Zhan,et al.  Wear Transitions in Particulate Reinforced Copper Matrix Composites , 2004 .

[23]  F. Maglia,et al.  Self-propagating high-temperature synthesis of functionally graded materials as thermal protection systems for high-temperature applications , 2003 .

[24]  Chao-Yang Wang,et al.  Modeling the solidification of functionally graded materials by centrifugal casting , 2000 .

[25]  F. Kennedy,et al.  The friction and wear of Cu-based silicon carbide particulate metaal matrix composites for brake applications , 1997 .