Sustainability in extrusion-based additive manufacturing technologies

[1]  Jonathan Edgar,et al.  “Additive Manufacturing Technologies: 3D Printing, Rapid Prototyping, and Direct Digital Manufacturing”, 2nd Edition , 2015 .

[2]  Jaroslaw Kotlinski,et al.  Mechanical properties of commercial rapid prototyping materials , 2014 .

[3]  Neri Volpato,et al.  The influence of support base on FDM accuracy in Z , 2014 .

[4]  Ismail Durgun,et al.  Experimental investigation of FDM process for improvement of mechanical properties and production cost , 2014 .

[5]  Alain Bernard,et al.  Using AM feature and multi-attribute decision making to orientate part in Additive Manufacturing , 2013 .

[6]  P. Vijay,et al.  Critical Parameters Effecting the Rapid Prototyping Surface Finish , 2012 .

[7]  Srinivasa Prakash Regalla,et al.  Optimization of Support Material and Build Time in Fused Deposition Modeling (FDM) , 2011 .

[8]  P. Bártolo,et al.  Integrated strategy for sustainable product development , 2011 .

[9]  Neil Hopkinson,et al.  Effect of section thickness and build orientation on tensile properties and material characteristics of laser sintered nylon‐12 parts , 2011 .

[10]  A. K. Sood,et al.  Improving dimensional accuracy of Fused Deposition Modelling processed part using grey Taguchi method , 2009 .

[11]  David Pennington,et al.  Recent developments in Life Cycle Assessment. , 2009, Journal of environmental management.

[12]  Henrique A. Almeida,et al.  Rapid prototyping and manufacturing for tissue engineering scaffolds , 2009, Int. J. Comput. Appl. Technol..

[13]  Caroline Sunyong Lee,et al.  Measurement of anisotropic compressive strength of rapid prototyping parts , 2007 .

[14]  Neil Hopkinson,et al.  Investigating mechanical anisotropy and end-of-vector effect in laser-sintered nylon parts , 2006 .

[15]  Richard J.M. Hague,et al.  Unlocking the Design Potential of Rapid Manufacturing , 2006 .

[16]  Neil Hopkinson,et al.  Rapid manufacturing : an industrial revolution for the digital age , 2006 .

[17]  N. Jawahar,et al.  Optimization of stereolithography process parameters for part strength using design of experiments , 2006 .

[18]  K. Leong,et al.  Investigation of the mechanical properties and porosity relationships in fused deposition modelling‐fabricated porous structures , 2006 .

[19]  N. Venkata Reddy,et al.  Optimum part deposition orientation in fused deposition modeling , 2004 .

[20]  Leong Kah Fai,et al.  Rapid Prototyping: Principles and Applications in Manufacturing , 2003 .

[21]  K. Leong,et al.  Rapid Prototyping: Principles and Applications (with Companion CD-ROM) , 2003 .

[22]  S. Arunachalam,et al.  Critical parameters influencing the quality of prototypes in fused deposition modelling , 2001 .

[23]  Duc Truong Pham,et al.  Rapid Manufacturing: The Technologies and Applications of Rapid Prototyping and Rapid Tooling , 2001 .

[24]  Seth Allen,et al.  Part orientation and build cost determination in layered manufacturing , 1998, Comput. Aided Des..

[25]  K.K.B. Hon,et al.  Optimising build parameters for improved surface finish in stereolithography , 1998 .

[26]  I. Gibson,et al.  Material properties and fabrication parameters in selective laser sintering process , 1997 .

[27]  H. Kristiansen,et al.  FLOW BOILING HEAT TRANSFER OF ELECTRONIC CHIPS IN HORIZONTAL CHANNELS , 1995 .

[28]  Ian Gibson,et al.  Additive manufacturing technologies : 3D printing, rapid prototyping, and direct digital manufacturing , 2015 .

[29]  David W. Rosen,et al.  What are Principles for Design for Additive Manufacturing , 2014 .

[30]  S. Marya,et al.  “Materials Science” Challenges in the Additive Manufacturing of Industrial Parts , 2014 .

[31]  Anoop Kumar Sood,et al.  Experimental investigation and empirical modelling of FDM process for compressive strength improvement , 2012 .

[32]  J. Urbanic,et al.  An Experimental Study to Determine Geometric and Dimensional Accuracy Impact Factors for Fused Deposition Modelled Parts , 2012 .

[33]  Farshad Amiraslani,et al.  Combating desertification in Iran over the last 50 years: an overview of changing approaches. , 2011, Journal of environmental management.

[34]  Siba Sankar Mahapatra,et al.  Prediction of dimensional accuracy in fused deposition modelling: a fuzzy logic approach , 2011 .

[35]  Ryan B. Wicker,et al.  Effects of build orientation on tensile strength for stereolithography-manufactured ASTM D-638 type I specimens , 2010 .

[36]  David L. Bourell,et al.  Sustainability issues in laser-based additive manufacturing , 2010 .

[37]  A. K. Sood,et al.  Parametric appraisal of mechanical property of fused deposition modelling processed parts , 2010 .

[38]  Steven J. Skerlos,et al.  Environmental aspects of laser-based and conventional tool and die manufacturing , 2007 .

[39]  Vicky Lofthouse,et al.  Ecodesign tools for designers: defining the requirements , 2006 .

[40]  Antonio Armillotta,et al.  Assessment of surface quality on textured FDM prototypes , 2006 .

[41]  Mark Hadfield,et al.  A sustainable product design model , 2006 .

[42]  M. Goedkoop,et al.  The Eco-indicator 99, A damage oriented method for Life Cycle Impact Assessment , 1999 .

[43]  Kunwoo Lee,et al.  Principles of CAD/CAM/CAE Systems , 1999 .

[44]  R. Crawford,et al.  Solid Freeform Fabrication: A New Direction in Manufacturing , 1997 .

[45]  Seth Allen,et al.  On the Computation Of Part Orientation Using Support Structures in Layered Manufacturing , 1994 .