Impact Analysis of Conducted Emission Measurement Without LISN

Common-mode (CM) and differential-mode (DM) conducted emissions without the line impedance stabilization network (LISN) is investigated. Using a switched-mode power supply (SMPS) as an equipment under test (EUT), the in-circuit CM and DM impedances of the actual measurement setup with and without LISN are extracted so that the impact on conducted emission measurement without LISN can be better understood.

[1]  Yie-Tone Chen,et al.  A procedure for designing EMI filters for AC line applications , 1996 .

[2]  John Malack,et al.  RF Impedance of United States and European Power Lines , 1976, IEEE Transactions on Electromagnetic Compatibility.

[3]  Christos Christopoulos,et al.  Introduction to Electromagnetic Compatibility , 2007 .

[4]  A. Perez,et al.  Common and differential mode characterization of EMI power-line filters from S-parameters measurements , 2004, 2004 International Symposium on Electromagnetic Compatibility (IEEE Cat. No.04CH37559).

[5]  John A. Malack,et al.  RF Impedance of Power Lines and Line Impedance Stabilization Networks in Conducted Interference Measurements , 1973 .

[6]  D. Sable,et al.  Measurement of noise source impedance of off-line converters , 2000 .

[7]  Arthur van Roermund,et al.  ‘Live’ mains impedance measurement and analysis , 2013, 2013 International Symposium on Electromagnetic Compatibility.

[8]  W. Eberle,et al.  A novel EMI filter design method for switching power supplies , 2004, IEEE Transactions on Power Electronics.

[9]  M. Sadiku.  Electromagnetic compatibility , 1992, IEEE Potentials.

[10]  Dongbing Zhang,et al.  A new method to characterize EMI filters , 1998, APEC '98 Thirteenth Annual Applied Power Electronics Conference and Exposition.

[11]  Kye Yak See,et al.  Systematic Electromagnetic Interference Filter Design Based on Information From In-Circuit Impedance Measurements , 2010, IEEE Transactions on Electromagnetic Compatibility.

[12]  H. Morel,et al.  State variable modeling of the power pin diode using an explicit approximation of semiconductor device equations: a novel approach , 1994 .

[13]  John C. Fluke.  Controlling Conducted Emissions by Design , 1991 .

[14]  P. L. So,et al.  Modeling and Analysis of Common-Mode Current Propagation in Broadband Power-Line Communication Networks , 2008, IEEE Transactions on Power Delivery.

[15]  Kye Yak See,et al.  Inductive Coupled In-Circuit Impedance Monitoring of Electrical System Using Two-Port ABCD Network Approach , 2015, IEEE Transactions on Instrumentation and Measurement.

[16]  Toshiro Sato,et al.  Measurement of the source impedance of conducted emission using mode separable LISN: Conducted emission of a switching power supply , 2000 .

[17]  Zhang Lei,et al.  Determination of noise source and impedance for conducted EMI prediction of power converters by lumped circuit models , 2004, 2004 IEEE 35th Annual Power Electronics Specialists Conference (IEEE Cat. No.04CH37551).

[18]  Mark J. Nave,et al.  Power line filter design for switched-mode power supplies , 2010 .

[19]  Kye Yak See,et al.  Accurate Extraction of Noise Source Impedance of an SMPS Under Operating Conditions , 2010, IEEE Transactions on Power Electronics.

[20]  Eric Laboure,et al.  Electromagnetic Compatibility in Power Electronics , 2014 .

[21]  J. D. van Wyk,et al.  Problematic aspects when using a LISN for converter EMI characterisation , 2013, 2013 IEEE International Conference on Industrial Technology (ICIT).

[22]  Roger A. Southwick.  Comments on "RF Impedance of Power Lines and Line Impedance Stabilization Networks in Conducted Interference Measurements" , 1973 .

[23]  Kye Yak See,et al.  Measurement of noise source impedance of SMPS using a two probes approach , 2004 .

[24]  C. Paul.  Introduction to electromagnetic compatibility , 2005 .

[25]  A. Perez,et al.  Characterization of Power-Line Filters and Electronic Equipment for Prediction of Conducted Emissions , 2008, IEEE Transactions on Electromagnetic Compatibility.