A complex programmable logic device-based high-precision electrical capacitance tomography system

In this paper, a high-precision measurement system for electrical capacitance tomography (ECT) is presented. A low-cost complex programmable logic device (CPLD) is employed to accomplish logic control, signal generation, data acquisition, digital demodulation and communication with the aid of external components. By adopting a simple digital demodulator recently developed by the authors, the demodulation to ac signals becomes rather simple and resource-saving. A double-T-switches configuration is developed to improve the precision and lower the limit of multi-channel capacitance measurement. A capacitance network is constructed for system calibration. A square ECT sensor with 16 electrodes is constructed to test the practical performance of the measurement system. With a data acquisition rate of 185 frame s−1, the signal-to-noise ratio and standard deviation of capacitance measurement can reach up to 70 dB and 0.09 fF, respectively. Image reconstruction experiment has validated the CPLD-based ECT system.

[1]  Wuqiang Yang,et al.  New AC-based capacitance tomography system , 1999 .

[2]  Shangchun Fan,et al.  A digital demodulation method for electrical tomography based on sine wave rectification , 2012, 2012 IEEE International Conference on Imaging Systems and Techniques Proceedings.

[3]  Wuqiang Yang,et al.  Development of capacitance tomographic imaging systems for oil pipeline measurements , 1995 .

[4]  Wuqiang Yang,et al.  A high-performance digital system for electrical capacitance tomography , 2011 .

[5]  Wuqiang Yang,et al.  High frequency and high resolution capacitance measuring circuit for process tomography , 1994 .

[6]  Bin Zhou,et al.  AC‐based Capacitance Tomography System With Small‐diameter And High‐pressure Pipe , 2007 .

[7]  A. N. Tikhonov,et al.  Solutions of ill-posed problems , 1977 .

[8]  Wuqiang Yang,et al.  The dynamic response of a Butterworth low-pass filter in an ac-based electrical capacitance tomography system , 2010 .

[9]  Zhiyao Huang,et al.  A high-speed data acquisition system for ECT based on the differential sampling method , 2005 .

[10]  Lei Tang,et al.  A Specific Data Acquisition Scheme for Electrical Tomography , 2008, 2008 IEEE Instrumentation and Measurement Technology Conference.

[11]  Zhiyao Huang,et al.  Design of high-speed ECT and ERT system , 2009 .

[12]  Wuqiang Yang,et al.  Hardware design of electrical capacitance tomography systems , 1996 .

[13]  Huaxiang Wang,et al.  Electrical Capacitance Tomography for Sensors of Square Cross Sections Using Calderon's Method , 2011, IEEE Transactions on Instrumentation and Measurement.

[14]  A. Gonzalez-Nakazawa,et al.  Transient processes and noise in a tomography system: an analytical case study , 2005, IEEE Sensors Journal.

[15]  Wuqiang Yang,et al.  Analysis of the effect of stray capacitance on an ac-based capacitance tomography transducer , 2003, IEEE Trans. Instrum. Meas..

[16]  Todd Pugsley,et al.  Application of electrical capacitance tomography to the fluidized bed drying of pharmaceutical granule , 2005 .

[17]  Feng Dong,et al.  Design of High Speed Cross Section Measurement System and its Real-Time Performance Analysis , 2007, 2007 International Conference on Machine Learning and Cybernetics.

[18]  Wuqiang Yang.  Further developments in an ac-based capacitance tomography system , 2001 .

[19]  Sheng Liu,et al.  Preliminary study on ECT imaging of flames in porous media , 2008 .

[20]  Haiqing Li,et al.  An Online Flow Pattern Identification System for Gas–Oil Two-Phase Flow Using Electrical Capacitance Tomography , 2006, IEEE Transactions on Instrumentation and Measurement.

[21]  Xingbin Liu,et al.  DC bias compensation in digital AC-based capacitance measurement for ECT , 2011, 2011 IEEE International Conference on Imaging Systems and Techniques.