Multi-objective optimization of gas metal arc welding parameters and sequences for low-carbon steel (Q345D) T-joints

Q345D high-quality low-carbon steel has been extensively employed in structures with stringent welding quality requirements. A multi-objective optimization of welding stress and deformation was presented to design reasonable values of gas metal arc welding parameters and sequences of Q345D T-joints. The optimized factors included continuous variables (welding current (I), welding voltage (U) and welding speed (v)) and discrete variables (welding sequence (S) and welding direction (D)). The concepts of the pointer and stack in Visual Basic (VB) and the interpolation method were introduced to optimize the variables. The optimization objectives included the different combinations of the angular distortion and transverse welding stress along the transverse and longitudinal distributions. Based on the design of experiments (DOE) and the polynomial regression (PR) model, the finite element (FE) results of the T-joint were used to establish the mathematical models. The Pareto front and the compromise solutions were obtained by using a multi-objective particle swarm optimization (MOPSO) algorithm. The optimal results were validated by the corresponding results of the FE method, and the error between the FE results and the two-objective results as well as that between the FE results and the three-objective optimization results were less than 17.2% and 21.5%, respectively. The influence and setting regularity of different factors were discussed according to the compromise solutions.

[1]  J. T. Maximov,et al.  Fatigue life enhancement of welded stiffened S355 steel plates with noncircular openings , 2015 .

[2]  M. Prażmowski,et al.  Study on material property changes of mild steel S355 caused by block loads with varying mean stress , 2015 .

[3]  T. Teng,et al.  Analysis of residual stresses and distortions in T-joint fillet welds , 2001 .

[4]  John Goldak,et al.  Combinatorial optimization of weld sequence by using a surrogate model to mitigate a weld distortion , 2011 .

[5]  P. Sathiya,et al.  Multi-objective Optimization of Continuous Drive Friction Welding Process Parameters Using Response Surface Methodology with Intelligent Optimization Algorithm , 2015 .

[6]  Ghalib Tham,et al.  Optimization and modeling of spot welding parameters with simultaneous multiple response consideration using multi-objective Taguchi method and RSM , 2012 .

[7]  Andy J. Keane,et al.  Weld sequence optimization: The use of surrogate models for solving sequential combinatorial problems , 2005 .

[8]  S. Feli,et al.  3-D numerical evaluation of residual stress and deformation due welding process using simplified heat source models , 2015 .

[9]  D. Radaj.  Heat Effects of Welding: Temperature Field, Residual Stress, Distortion , 1992 .

[10]  Mohd Ridhwan Mohammed Redza,et al.  Simulation and experimental study on distortion of butt and T-joints using WELD PLANNER , 2011 .

[11]  M. H. Kadivar,et al.  Optimizing welding sequence with genetic algorithm , 2000 .

[12]  J. Goldak,et al.  A new finite element model for welding heat sources , 1984 .

[13]  P. Sathiya,et al.  Prediction and optimization of friction welding parameters for super duplex stainless steel (UNS S32760) joints , 2014 .

[14]  Carlos A. Coello Coello,et al.  Handling multiple objectives with particle swarm optimization , 2004, IEEE Transactions on Evolutionary Computation.

[15]  Mohammad Hassan Shojaeefard,et al.  Multi objective optimization of friction stir welding parameters using FEM and neural network , 2014, International Journal of Precision Engineering and Manufacturing.

[16]  Karen A. F. Copeland.  Design and Analysis of Experiments, 5th Ed. , 2001 .

[17]  Yinghui Wei,et al.  Evaluation on Fatigue Performance and Fracture Mechanism of Laser Welded TWIP Steel Joint Based on Evolution of Microstructure and Micromechanical Properties , 2016 .

[18]  Jeong-Ung Park,et al.  Effect of welding sequence to minimize fillet welding distortion in a ship’s small component fabrication using joint rigidity method , 2016 .

[19]  Q. G. Meng,et al.  Influence of a welding sequence on the welding residual stress of a thick plate , 2005 .

[20]  Rahul Chhibber,et al.  Effect of welding parameters on bead profile, microhardness and H2 content in submerged arc welding of high-strength low-alloy steel , 2014 .

[21]  S. Ohnimus,et al.  Influence of clamping on distortion of welded S355 T-joints , 2009 .

[22]  Ezio Cadoni,et al.  High strain rate response of S355 at high temperatures , 2016 .

[23]  Khalil Khalili,et al.  Multi-objective Optimization of Welding Parameters in Submerged Arc Welding of API X65 Steel Plates , 2015 .