Characterization of low-temperature wafer bonding using thin-film parylene

This paper presents detailed experimental data on wafer bonding using a thin Parylene layer, and reports results on: 1) bond strength and its dependence on bonding temperature, bonding force, ambient pressure (vacuum), and time, 2) bond strength variation and stability up to two years post bond, and 3) bond strength variation after exposure to process chemicals. Wafer bonding using thin (<381 nm) Parylene intermediate layers on each wafer in a standard commercial bonder and aligner has been successfully developed. The Parylene bond strength is optimized at 230/spl deg/C, although Parylene bonding is possible at as low as 130/spl deg/C. The optimized bonding conditions are a low-temperature of /spl sim/230/spl deg/C, a vacuum of /spl sim/ 0.153 mbar, and 800 N force on a 100 mm wafer. The resultant Parylene bond strength is 3.60 MPa, and the strength for wafers bonded at or above 210/spl deg/C is maintained within 93% of its original value after two years. The bond strength is also measured after exposure to several process chemicals. The bond strength was reduced most in undiluted AZ400K (base) by 69% after one week, then in BHF (acid), MF319 (base), Acetone (solvent), and IPA (solvent) by 56%, 33%, 20%, and 8%, respectively, although less than one hour exposure to these chemicals did not cause a significant bond strength change (less than 11%). [1487].

[1]  Yong Xu,et al.  IC-integrated flexible shear-stress sensor skin , 2003 .

[2]  C. Ageorges,et al.  Fusion Bonding of Polymer Composites , 2002 .

[3]  Yoonsu Choi,et al.  Rapid, low-cost fabrication of parylene microchannels for microfluidic applications , 2003, TRANSDUCERS '03. 12th International Conference on Solid-State Sensors, Actuators and Microsystems. Digest of Technical Papers (Cat. No.03TH8664).

[4]  W. Smith.  Foundations of Materials Science and Engineering , 1993 .

[5]  Y. Tai,et al.  Design, fabrication, and testing of micromachined silicone rubber membrane valves , 1999 .

[6]  S. Bhansali,et al.  A low temperature biochemically compatible bonding technique using fluoropolymers for biochemical microfluidic systems , 2000, Proceedings IEEE Thirteenth Annual International Conference on Micro Electro Mechanical Systems (Cat. No.00CH36308).

[7]  R. Howe,et al.  Batch transfer of microstructures using flip-chip solder bonding , 1999 .

[8]  Y. Tai,et al.  A check-valved silicone diaphragm pump , 2000, Proceedings IEEE Thirteenth Annual International Conference on Micro Electro Mechanical Systems (Cat. No.00CH36308).

[9]  Anders Kristensen,et al.  PMMA to SU-8 bonding for polymer based lab-on-a-chip systems with integrated optics , 2004 .

[10]  Stefan Bengtsson,et al.  Formation of Silicon Structures by Plasma‐Activated Wafer Bonding , 2000 .

[11]  K. Najafi,et al.  Wafer bonding using parylene and wafer-level transfer of free-standing parylene membranes , 2003, TRANSDUCERS '03. 12th International Conference on Solid-State Sensors, Actuators and Microsystems. Digest of Technical Papers (Cat. No.03TH8664).

[12]  Dong Sung Kim,et al.  A novel low temperature bonding technique for plastic substrates using X-ray irradiation , 2003, TRANSDUCERS '03. 12th International Conference on Solid-State Sensors, Actuators and Microsystems. Digest of Technical Papers (Cat. No.03TH8664).

[13]  G. Stemme,et al.  Void-free full wafer adhesive bonding , 2000, Proceedings IEEE Thirteenth Annual International Conference on Micro Electro Mechanical Systems (Cat. No.00CH36308).

[14]  S. Bhansali,et al.  A low-temperature bonding technique using spin-on fluorocarbon polymers to assemble microsystems , 2002 .

[15]  Yu-Chong Tai,et al.  Microsensors and actuators for macrofluidic control , 2004, IEEE Sensors Journal.

[16]  Y. Mei.  A Robust Gold-Silicon Eutectic Wafer Bonding Technology for Vacuum Packaging , 2002 .

[17]  M. Esashi,et al.  The structures for electrostatic servo capacitive vacuum sensors , 1998 .

[18]  Yu-Chuan Su,et al.  Localized plastic bonding for micro assembly, packaging and liquid encapsulation , 2001, Technical Digest. MEMS 2001. 14th IEEE International Conference on Micro Electro Mechanical Systems (Cat. No.01CH37090).

[19]  Khalil Najafi,et al.  High-Density Micromachined Acoustic Ejector Array For Micro Propulsion , 2001 .

[20]  K. Moon,et al.  Wafer bonding using microwave heating of parylene intermediate layers , 2004 .

[21]  Kurt E. Petersen,et al.  Variable-flow microvalve structure fabricated with silicon fusion bonding , 1990, IEEE 4th Technical Digest on Solid-State Sensor and Actuator Workshop.

[22]  Srinivas Tadigadapa,et al.  Tin-based solder bonding for MEMS fabrication and packaging applications , 2004 .

[23]  B. Ziaie,et al.  Silicon wafer bonding with an insulator interlayer using RF dielectric heating , 2002, Technical Digest. MEMS 2002 IEEE International Conference. Fifteenth IEEE International Conference on Micro Electro Mechanical Systems (Cat. No.02CH37266).

[24]  George M. Whitesides,et al.  Microfluidics Section: Design and Fabrication of Integrated Passive Valves and Pumps for Flexible Polymer 3-Dimensional Microfluidic Systems , 2002 .

[25]  M. Richter,et al.  A bidirectional silicon micropump , 1995 .

[26]  J. Lasky.  Wafer bonding for silicon‐on‐insulator technologies , 1986 .