Highly-multiplexed microwave SQUID readout using the SLAC Microresonator Radio Frequency (SMuRF) electronics for future CMB and sub-millimeter surveys

The next generation of cryogenic CMB and submillimeter cameras under development require densely instrumented sensor arrays to meet their science goals. The readout of large numbers (~10,000-100,000 per camera) of sub-Kelvin sensors, for instance as proposed for the CMB-S4 experiment, will require substantial improvements in cold and warm readout techniques. To reduce the readout cost per sensor and integration complexity, efforts are presently focused on achieving higher multiplexing density while maintaining readout noise subdominant to intrinsic detector noise and presenting manageable thermal loads. Highly-multiplexed cold readout technologies in active development include Microwave Kinetic Inductance Sensors (MKIDs) and microwave rf-SQUIDs. Both exploit the high quality factors of superconducting microwave resonators to densely channelize sub-Kelvin sensors into the bandwidth of a microwave transmission line. In the case of microwave SQUID multiplexing, arrays of transition-edge sensors (TES) are multiplexed by coupling each TES to its own superconducting microwave resonator through an rf-SQUID. We present advancements in the development of a new warm readout system for microwave SQUID multiplexing, the SLAC Superconducting Microresonator RF electronics, or SMuRF, by adapting SLAC National Accelerator Laboratory's Advanced Telecommunications Computing Architecture (ATCA) FPGA Common Platform. SMuRF aims to read out 4000 microwave SQUID channels between 4 and 8 GHz per RF line. Each compact SMuRF system is built onto a single ATCA carrier blade. Daughter boards on the blade implement RF frequency-division multiplexing using FPGAs, fast DACs and ADCs, and an analog up- and down-conversion chain. The system reads out changes in flux in each resonator-coupled rf-SQUID by monitoring the change in the transmitted amplitude and frequency of RF tones produced at each resonator's fundamental frequency. The SMuRF system is unique in its ability to track each tone, minimizing the total RF power required to readout each resonator, thereby significantly reducing the linearity requirements on the cold and warm readout. Here, we present measurements of the readout noise and linearity of the first full SMuRF system, including a demonstration of closed-loop tone tracking on a 528 channel cryogenic microwave SQUID multiplexer. SMuRF is being explored as a potential readout solution for a number of future CMB projects including Simons Observatory, BICEP Array, CCAT-prime, Ali-CPT, and CMB-S4. In addition, parallel development of the platform is underway to adapt SMuRF to read out both MKID and fast X-ray TES calorimeter arrays.

[1]  Neil Rowlands,et al.  Digital frequency domain multiplexing readout electronics for the next generation of millimeter telescopes , 2014, Astronomical Telescopes and Instrumentation.

[2]  R. Kaul,et al.  Microwave engineering , 1989, IEEE Potentials.

[3]  K. Irwin,et al.  Evaluation of a Microwave SQUID Multiplexer Prototype , 2007, IEEE Transactions on Applied Superconductivity.

[4]  Adrian T. Lee,et al.  CMB-S4 Science Book, First Edition , 2016, 1610.02743.

[5]  Di Wu,et al.  Probing primordial gravitational waves: Ali CMB Polarization Telescope , 2017, National science review.

[6]  S. Foreman,et al.  CCAT-Prime: science with an ultra-widefield submillimeter observatory on Cerro Chajnantor , 2018, Astronomical Telescopes + Instrumentation.

[7]  Shaul Hanany,et al.  CMB-S4 Technology Book, First Edition , 2017, 1706.02464.

[8]  Andrew Siemion,et al.  A Decade of Developing Radio-Astronomy Instrumentation using CASPER Open-Source Technology , 2016, 1611.01826.

[9]  Martin Grim,et al.  Multiplexed Readout for 1000-Pixel Arrays of Microwave Kinetic Inductance Detectors , 2016, IEEE Transactions on Microwave Theory and Techniques.

[10]  A. Giachero,et al.  Development of microwave-multiplexed superconductive detectors for the HOLMES experiment , 2016, 1601.03970.

[11]  Shannon M. Duff,et al.  Advanced ACTPol Multichroic Polarimeter Array Fabrication Process for 150 mm Wafers , 2016 .

[12]  Kent D. Irwin,et al.  Flux-Ramp Modulation for SQUID Multiplexing , 2012 .

[13]  J. E. Ruhl,et al.  Fabrication of large dual-polarized multichroic TES bolometer arrays for CMB measurements with the SPT-3G camera , 2015 .

[14]  Bradley K. Alpert,et al.  TES X-ray Spectrometer at SLAC LCLS-II , 2018, Journal of Low Temperature Physics.

[15]  Tom Bova,et al.  RELIABLE UDP PROTOCOL , 1999 .

[16]  H. Leduc,et al.  A broadband superconducting detector suitable for use in large arrays , 2003, Nature.

[17]  Dan Werthimer,et al.  A readout for large arrays of microwave kinetic inductance detectors. , 2012, The Review of scientific instruments.

[18]  Johnathon D. Gard,et al.  Development of ROACH Firmware for Microwave Multiplexed X-Ray TES Microcalorimeters , 2017, IEEE Transactions on Applied Superconductivity.

[19]  Bradley Dober,et al.  Simultaneous readout of 128 X-ray and gamma-ray transition-edge microcalorimeters using microwave SQUID multiplexing , 2017 .

[20]  Edward J. Wollack,et al.  Advanced ACTPol Cryogenic Detector Arrays and Readout , 2015, 1510.02809.

[21]  Kent D. Irwin,et al.  Microwave SQUID multiplexer , 2004 .

[22]  Jonas Zmuidzinas,et al.  Superconducting Microresonators: Physics and Applications , 2012 .

[23]  Edward J. Wollack,et al.  Characterization of the Mid-Frequency Arrays for Advanced ACTPol , 2017, Journal of Low Temperature Physics.

[24]  Richard O. Claus,et al.  A FPGA Based Common Platform for LCLS2 Beam Diagnostics and Controls , 2017 .

[25]  Daniel R. Schmidt,et al.  A Scalable Readout for Microwave SQUID Multiplexing of Transition-Edge Sensors , 2018, Journal of Low Temperature Physics.

[26]  P. A. R. Ade,et al.  SPT-3G: A Multichroic Receiver for the South Pole Telescope , 2018, Journal of Low Temperature Physics.

[27]  Hsiao-Mei Cho,et al.  Readout of two-kilopixel transition-edge sensor arrays for Advanced ACTPol , 2016, Astronomical Telescopes + Instrumentation.

[28]  A. Gilbert,et al.  The Polarbear-2 and the Simons Array Experiments , 2015, 1512.07299.

[29]  Richard O. Claus,et al.  The SLAC Common-Platform Firmware for High-Performance Systems , 2018 .

[30]  Bradley Dober,et al.  SLAC Microresonator Radio Frequency (SMuRF) Electronics for Read Out of Frequency-Division-Multiplexed Cryogenic Sensors , 2018, Journal of Low Temperature Physics.

[31]  A. G. Vieregg,et al.  BICEP3 performance overview and planned Keck Array upgrade , 2016, Astronomical Telescopes + Instrumentation.

[32]  Andrew S. Hoover,et al.  Integration of TES Microcalorimeters With Microwave SQUID Multiplexed Readout , 2015, IEEE Transactions on Applied Superconductivity.

[33]  Gabriel M. Rebeiz,et al.  Multi-chroic Dual-Polarization Bolometric Focal Plane for Studies of the Cosmic Microwave Background , 2012 .

[34]  Jason E. Austermann,et al.  Readout demonstration of 512 TES bolometers using a single microwave SQUID multiplexer (Conference Presentation) , 2018, Millimeter, Submillimeter, and Far-Infrared Detectors and Instrumentation for Astronomy IX.

[35]  G. Hilton,et al.  Development of a Microwave SQUID-Multiplexed TES Array for MUSTANG-2 , 2016 .

[36]  Jonas Zmuidzinas,et al.  Noise properties of superconducting coplanar waveguide microwave resonators , 2006, cond-mat/0609614.

[37]  P. Wilson,et al.  An open-source readout for MKIDs , 2010, Astronomical Telescopes + Instrumentation.