Limit analysis of masonry vaults by means of curved shell finite elements and homogenization

Abstract The study of masonry vaults should take into account the essentials of the material “masonry” – i.e. heterogeneity, almost no resistance to tension combined with a good compressive strength and a high friction coefficient, as well as the overall importance of the geometry for achieving the equilibrium. In this paper, a new six-noded triangular curved element, specifically developed for the kinematic limit analysis of masonry shells, is presented. Plastic dissipation is allowed only at the interfaces (generalized cylindrical hinges) between adjoining elements for combined membrane actions, bending moment, torsion and out-of-plane shear, as it is required for the analysis of thick (Reissner–Mindlin) shells. An upper bound of the collapse load is so obtained, since, looking at the dual formulation, the admissibility of the stress state is imposed only at the element boundaries. Masonry strength domain at each interface between contiguous triangular elements is evaluated resorting to a suitable upper bound FE homogenization procedure. The model is assessed through several numerical simulations on a number of masonry shells experimentally tested until collapse. In particular, the dependence of the collapse multiplier on the mesh and on the material parameters (sensitivity analysis) is thoroughly discussed.

[1]  Scott W. Sloan,et al.  A new discontinuous upper bound limit analysis formulation , 2005 .

[2]  Nicola Zani,et al.  The Maximum Modulus Eccentricities Surface for Masonry Vaults and Limit Analysis , 1999 .

[3]  Anna Saetta,et al.  Analyses of Masonry Vaults: A Macro Approach based on Three-Dimensional Damage Model , 2002 .

[4]  Paulo B. Lourenço,et al.  Cap Model for Limit Analysis and Strengthening of Masonry Structures , 2003 .

[5]  Andrea Cianchi,et al.  Optimal Spherical Masonry Domes of Uniform Strength , 1997 .

[6]  AT Ad Vermeltfoort.  Analysis and experiments of masonry arches , 2001 .

[7]  Scott W. Sloan,et al.  Three-dimensional Mohr-Coulomb limit analysis using semidefinite programming , 2007 .

[8]  Dermot O'Dwyer,et al.  Funicular analysis of masonry vaults , 1999 .

[9]  G. Felice,et al.  A homogenization approach to the ultimate strength of brick masonry , 1997 .

[10]  A. Anthoine,et al.  NUMERICAL STRATEGIES FOR SOLVING CONTINUUM DAMAGE PROBLEMS WITH SOFTENING:APPLICATION TO THE HOMOGENIZATION OF MASONRY , 1997 .

[11]  Gabriele Milani,et al.  Homogenised limit analysis of masonry walls, Part II: Structural examples , 2006 .

[12]  Santiago Sánchez-Cervera Huerta,et al.  Mechanics of masonry vaults: The equilibrium approach , 2001 .

[13]  Paulo B. Lourenço.  ASSESSMENT, DIAGNOSIS AND STRENGTHENING OF OUTEIRO CHURCH, PORTUGAL , 2005 .

[14]  P. Lourenço,et al.  Three-dimensional limit analysis of rigid blocks assemblages. Part I: Torsion failure on frictional interfaces and limit analysis formulation , 2005 .

[15]  Jacques Heyman,et al.  The safety of masonry arches , 1969 .

[16]  A. Barbieri,et al.  MASONRY ORTHOTROPIC VAULTS IN HISTORICAL CONSTRUCTION : THE HERRINGBONE PATTERN TECHNOLOGY , 2022 .

[17]  Georgios E. Stavroulakis,et al.  Limit analysis of a single span masonry bridge with unilateral frictional contact interfaces , 2006 .

[18]  F. López-Almansa,et al.  Limit analysis of reinforced masonry vaults , 2007 .

[19]  Paulo B. Lourenço,et al.  Abbreviated Title : Homogenised limit analysis of masonry , failure surfaces , 2007 .

[20]  S. Sloan,et al.  Formulation and solution of some plasticity problems as conic programs , 2007 .

[21]  Massimiliano Lucchesi,et al.  On the Collapse of Masonry Arches , 1997 .

[22]  Rhj Ron Peerlings,et al.  Mesoscopic modeling of failure and damage-induced anisotropy in brick masonry , 2004 .

[23]  J. Z. Zhu,et al.  The finite element method , 1977 .

[24]  S. Sloan,et al.  Upper bound limit analysis using discontinuous velocity fields , 1995 .

[25]  Abderrahmane Habbal.  An effective model for Lipschitz wrinkled arches , 2003 .

[26]  Gabriele Milani,et al.  A kinematic FE limit analysis model for thick English bond masonry walls , 2008 .

[27]  Paolo Faccio,et al.  Volte in muratura con rinforzi in FRP , 1999 .

[28]  Paulo B. Lourenço,et al.  Homogenization approach for the limit analysis of out-of-plane loaded masonry walls , 2006 .

[29]  M. Ferris,et al.  Limit Analysis of Frictional Block Assemblies as a Mathematical Program With Complementarity Constraints , 2001 .

[30]  Paulo B. Lourenço,et al.  A plane stress softening plasticity model for orthotropic materials , 1997 .

[31]  Edoardo Benvenuto.  Vaulted structures and elastic systems , 1991 .

[32]  Jacques Heyman.  Equilibrium of shell structures , 1977 .

[33]  Viktor E. Verijenko,et al.  Structural analysis of composite lattice shells of revolution on the basis of smearing stiffness , 2001 .

[34]  D. Chapelle,et al.  The Finite Element Analysis of Shells - Fundamentals , 2003 .

[35]  J. Awrejcewicz,et al.  Buckling analysis of discretely stringer-stiffened cylindrical shells , 2006 .

[36]  P. Lourenço,et al.  Multisurface Interface Model for Analysis of Masonry Structures , 1997 .

[37]  Philippe Block,et al.  Real-time limit analysis of vaulted masonry buildings , 2006 .

[38]  Irving J. Oppenheim,et al.  Limit State Analysis of Masonry Domes , 1989 .

[39]  Gabriele Milani,et al.  A Reissner–Mindlin limit analysis model for out-of-plane loaded running bond masonry walls , 2007 .

[40]  Paulo B. Lourenço,et al.  Anisotropic Softening Model for Masonry Plates and Shells , 2000 .

[41]  Dina D'Ayala,et al.  Limit state analysis of hemispherical domes with finite friction , 2001 .

[42]  C. Martin,et al.  Lower bound limit analysis of cohesive‐frictional materials using second‐order cone programming , 2006 .