A 3D numerical model of an ONAN distribution transformer

Abstract The aim of this work is to validate a numerical model used to simulate the natural convection in a distribution transformer. The transformer of interest is of the oil natural air natural (ONAN) type and the model seeks to obtain the temperature and velocity fields in the oil volume. The simulation domain reproduces a slice model developed for a previous experimental study. In the numerical model, the heating element, which consists of a series of parallel heating channels, was simplified into a permeable medium. The numerical study was carried out by applying the Finite Element Method to solve the 3D Navier-Stokes and heat equations using the in-house developed Par-GPFEP code. In order to validate the model, the numerical results obtained from the simulations were compared with the experimental measurements obtained from the existing experimental device (Cordoba et al., 2018). Despite the simplifications in the numerical model we found a satisfactory overall agreement between numerical and experimental results, both in heat transfer rates, temperature distribution and overall flow patterns. The simplification of the heating element causes differences in the behavior of the thermal plume immediately above it, but the effect seems to be local and not to affect significantly the overall convective flow.

[1]  Sebastian Valeriu Hudişteanu,et al.  Numerical Study of Cooling Solutions Inside a Power Transformer , 2017 .

[2]  Juan Carlos Ramos,et al.  Numerical modelling of natural convection of oil inside distribution transformers , 2011 .

[4]  Churl Yoon,et al.  Development of a CFD model for the CANDU-6 moderator analysis using a coupled solver , 2008 .

[5]  Suhaib Umer Ilyas,et al.  CFD Analysis of Heat Transfer Performance of Nanofluids in Distributor Transformer , 2016 .

[6]  F. Torriano,et al.  Numerical and experimental thermofluid investigation of different disc-type power transformer winding arrangements , 2018 .

[7]  T. S. Ramu,et al.  Prediction of hottest spot temperature (HST) in power and station transformers , 2003 .

[8]  G. Su,et al.  Three dimensional thermal hydraulic characteristic analysis of reactor core based on porous media method , 2017 .

[9]  Haiqiong Xie,et al.  A lattice Boltzmann model for thermal flows through porous media , 2016 .

[10]  F. Torriano,et al.  Numerical study of parameters affecting the temperature distribution in a disc-type transformer winding , 2010 .

[11]  Frank P. Incropera,et al.  Fundamentals of Heat and Mass Transfer , 1981 .

[12]  Lei Wang,et al.  Effects of temperature-dependent properties on natural convection of nanofluids in a partially heated cubic enclosure , 2018 .

[13]  E. Dari,et al.  An experimental study of natural convection in a distribution transformer slice model , 2018, International Journal of Thermal Sciences.

[14]  Han Young Yoon,et al.  Multi-physics simulation of nuclear reactor core by coupled simulation using CUPID/MASTER , 2017 .

[15]  N. E. Wakil,et al.  Numerical study of heat transfer and fluid flow in a power transformer , 2006 .

[16]  Lattice-Boltzmann modeling of unstable flows amid arrays of wires , 2015 .

[17]  R. Amigo,et al.  Analysis of convection enhancing complex shaped adsorption vessels , 2018, Applied Thermal Engineering.

[18]  Chuan Zhang,et al.  Numerical analysis on the energy storage efficiency of phase change material embedded in finned metal foam with graded porosity , 2017 .

[19]  Sweng Woong Woo,et al.  Comparative study on the effect of reactor internal structure geometry modeling methods on the prediction accuracy for PWR internal flow distribution , 2014 .

[20]  Zhenyu Liu,et al.  Numerical modeling for solid–liquid phase change phenomena in porous media: Shell-and-tube type latent heat thermal energy storage , 2013 .

[21]  Ahmad Gholami,et al.  Temperature distribution in ONAN power transformer windings with finite element method , 2009 .

[22]  Y. Feldman,et al.  “Smart” passive thermal insulation of confined natural convection heat transfer: An application to hollow construction blocks , 2017 .

[23]  F. Duan,et al.  Non-uniform heat transfer suppression to enhance PCM melting by angled fins , 2018 .

[24]  E. Dari,et al.  Natural convection in a cubical cavity filled with a fluid showing temperature-dependent viscosity , 2015 .

[25]  Mikhail A. Sheremet,et al.  Transient natural convection with temperature-dependent viscosity in a square partially porous cavity having a heat-generating source , 2018, Numerical Heat Transfer, Part A: Applications.

[26]  Majid Siavashi,et al.  Heat transfer and entropy generation study of non-Darcy double-diffusive natural convection in inclined porous enclosures with different source configurations , 2017 .

[27]  F. Torriano,et al.  Numerical investigation of 3D flow and thermal effects in a disc-type transformer winding , 2012 .

[28]  Xiang Zhang,et al.  Numerical investigation of oil flow and temperature distributions for ON transformer windings , 2018 .

[29]  M. Lehtonen,et al.  Dynamic thermal modeling of power transformers: further Development-part II , 2006, IEEE Transactions on Power Delivery.

[30]  M. Lehtonen,et al.  Dynamic thermal modeling of distribution transformers , 2005, IEEE Transactions on Power Delivery.

[31]  Michael E. Cholette,et al.  Multi-layer PCM solidification in a finned triplex tube considering natural convection , 2017 .

[32]  J. Womersley.  Method for the calculation of velocity, rate of flow and viscous drag in arteries when the pressure gradient is known , 1955, The Journal of physiology.

[33]  Denis Flick,et al.  Transient heat transfer by free convection in a packed bed of spheres : Comparison between two modelling approaches and experimental results , 2008 .

[34]  Alistair Revell,et al.  Numerical prediction of local hot-spot phenomena in transformer windings , 2012 .

[35]  M. A. Taghikhani,et al.  Prediction of hottest spot temperature in power transformer windings with non-directed and directed oil-forced cooling , 2009 .