Analysis of Flip Chip Bonding for Performance Stability of UHF RFID Tags

Thermocompression bonding is one of the most important procedures in radio frequency identification tag fabrication because the electrical and mechanical properties of the joint greatly influence the overall tag performances. The characteristics of the joint are determined by the alignment between the microchip and antenna pads, the adhesives used, and various bonding parameters (temperature, pressure, and time). This paper uses an electrical equivalent circuit analysis, electromagnetic full-wave simulations, and environmental tests to investigate the factors that influence the reading performance of the flip chip bonding process. First, based on an equivalent circuit analysis of the bonded tag, the effect of the parasitic impedance on impedance matching and power transfer is analyzed. The parasitic impedance is then estimated by comparison with the measured impedance of the bonded chips. Second, we investigate the variation in the reading performance of the tag when various geometrical errors are generated at the joint between the microchip and the antenna. Finally, the bonding parameters for stable reading performance are studied by completing environmental tests. The results provide useful information for achieving stable reading performance of tags in flip chip bonding.

[1]  Yu-Min Lin,et al.  Development of a Novel Compliant-Bump Structure for ACA-Bonded Chip-on-Flex (COF) Interconnects With Ultra-Fine Pitch , 2011, IEEE Transactions on Components, Packaging and Manufacturing Technology.

[2]  Young-Ho Kim,et al.  A new COP bonding using non-conductive adhesives for LCDs driver IC packaging , 2006, Displays.

[3]  H. Gronqvist,et al.  Theoretical analysis of RF performance of anisotropic conductive adhesive flip- chip joints , 2004, IEEE Transactions on Components and Packaging Technologies.

[4]  Jin-Sang Hwang,et al.  Highly reliable non-conductive adhesives for flip chip CSP applications , 2003 .

[5]  Characteristics of a Novel Compliant Bump for 3-D Stacking With High-Density Inter-Chip Connections , 2011, IEEE Transactions on Components, Packaging and Manufacturing Technology.

[6]  J. Zhong,et al.  A review of the influencing factors on anisotropic conductive adhesives joining technology in electrical applications , 2008 .

[7]  S.F. Lam,et al.  Power reflection coefficient analysis for complex impedances in RFID tag design , 2005, IEEE Transactions on Microwave Theory and Techniques.

[8]  K. Paik,et al.  The contact resistance and reliability of anisotropically conductive film (ACF) , 1999, ECTC 1999.

[9]  Seongyoung Han,et al.  Issues in Assembly Process of Next-Generation Fine-Pitch Chip-On-Flex Packages for LCD Applications , 2007, IEEE Transactions on Advanced Packaging.

[10]  Y. Chan,et al.  Adhesive strength of flip chip packages , 2008 .

[11]  Laura Frisk,et al.  Effects of Cycling Humidity on the Performance of RFID Tags With ACA Joints , 2012, IEEE Transactions on Reliability.

[12]  Kyung-Wook Paik,et al.  Recent advances on anisotropic conductive adhesives (ACAs) for flat panel displays and semiconductor packaging applications , 2006 .

[13]  D. Staiculescu,et al.  Wideband scalable electrical model for microwave/millimeter wave flip chip interconnects , 2001 .

[14]  Jeongjoon Lee,et al.  Full Wave Simulation of Flip-Chip Packaging Effects on RFID Transponder , 2007, 2007 IEEE International Conference on RFID.

[15]  Hussein Hamed Mahmoud Ghouz,et al.  An accurate equivalent circuit model of flip chip and via interconnects , 1996 .

[16]  Daniel M. Dobkin,et al.  The RF in RFID: Passive UHF RFID in Practice , 2007 .

[17]  L. Frisk,et al.  Reliability Analysis of UHF RFID Tags Under a Combination of Environmental Stresses , 2013, IEEE Transactions on Device and Materials Reliability.

[18]  Soohyun Kim,et al.  Sliding Mechanism of Lateral Thermosonic Process With Anisotropic Conductive Film for High Productivity and High Reliability , 2013, IEEE Transactions on Components, Packaging and Manufacturing Technology.

[19]  G. Marrocco,et al.  The art of UHF RFID antenna design: impedance-matching and size-reduction techniques , 2008, IEEE Antennas and Propagation Magazine.

[20]  Zhong Chen,et al.  Development and reliability of non-conductive adhesive flip-chip packages , 2004 .

[21]  J. C. Jagt.  Reliability of electrically conductive adhesive joints for surface mount applications: a summary of the state of the art , 1998 .

[22]  W. Heinrich,et al.  Theory and measurements of flip-chip interconnects for frequencies up to 100 GHz , 2001 .

[23]  Manos M. Tentzeris,et al.  T-matching networks for the efficient matching of practical RFID tags , 2009, 2009 European Microwave Conference (EuMC).

[24]  Jong-Gwan Yook,et al.  Effects of a Metal Plane on a Meandered Slot Antenna for UHF RFID Applications , 2012 .

[25]  Andrzej Dziedzic.  Modern Microelectronic Technologies in Fabrication of RFID Tags , 2011 .