Validity and limitation of analytical models for the bending stress of a helical wire in unbonded flexible pipes

Abstract Unbonded flexible pipe is one of the important pieces of equipment in floating production systems for transport of oil and gas between floaters and subsea wells located in deep water. To assure safety over a long-term service period, analysis of fatigue behavior under alternative bending is a key requirement. An analytical model for prediction of bending behavior is essential for understanding the mechanism of the local stress distribution in the helical wires of the tension armor layers under alternative curvatures and rapid estimation of the service life of flexible pipes for designers in engineering practice. In this paper, seven analytical models available in the literature are selected and summarized. Although the experimental results reported in the literature are limited, a three-dimensional finite element model is developed for investigation of the seven models, and the validity and limitations of these models for different structural parameters of helical wire are discussed, i.e., the width-thickness ratio of the wire section and helical angle. The analytical model based on spring theory resulted in a satisfactory estimation of bending stress for most cases and is recommended as a tool for the basic design of the helical armor wire structures in flexible pipes.

[1]  George A. Costello.  Large Deflections of Helical Spring due to Bending , 1977 .

[2]  Thomas Clarke,et al.  Monitoring the structural integrity of a flexible riser during a full-scale fatigue test , 2011 .

[3]  Svein Sævik,et al.  Fatigue testing and theoretical studies of two 4 in flexible pipes , 1995 .

[4]  Svein Sævik,et al.  Armour Layer Fatigue Design Challenges for Flexible Risers in Ultra-Deep Water Depth , 2009 .

[5]  John Zhang,et al.  Effective Bending Stiffness of an Unbonded Flexible Riser , 2008 .

[6]  Anders Lyckegaard,et al.  A method for prediction of the equilibrium state of a long and slender wire on a frictionless toroid applied for analysis of flexible pipe structures , 2012 .

[7]  M. Lutchansky.  Axial Stresses in Armor Wires of Bent Submarine Cables , 1969 .

[8]  T. Hill,et al.  State of the Art Analytical Tools Improve Optimization of Unbonded Flexible Pipes for Deepwater Environments , 2003 .

[9]  José Renato M. de Sousa,et al.  A Theoretical Approach to Predict the Fatigue Life of Flexible Pipes , 2012, J. Appl. Math..

[10]  Michael Case,et al.  Higher Order Effects on Bending of Helical Armor Wire Inside an Unbonded Flexible Pipe , 2005 .

[11]  J.M.M. Out,et al.  Slippage of helical reinforcing on a bent cylinder , 1997 .

[12]  A. Love.  A treatise on the mathematical theory of elasticity , 1892 .

[13]  Edison Castro Prates de Lima,et al.  On the Tension-Compression Behaviour of Flexible Risers , 2003 .

[14]  Thomas Clarke,et al.  Monitoring the structural integrity of a flexible riser during dynamic loading with a combination of non-destructive testing methods , 2010 .

[15]  Geir Skeie,et al.  Efficient Fatigue Analysis of Helix Elements in Umbilicals and Flexible Risers , 2010 .

[16]  M. Raoof,et al.  Wire Stress Calculations in Helical Strands Undergoing Bending , 1992 .

[17]  Carlos Magluta,et al.  An Experimental Investigation on the Bending Behaviour of Flexible Pipes , 2003 .

[18]  J. A. Witz.  A case study in the cross-section analysis of flexible risers , 1996 .

[19]  Manfredo P. do Carmo,et al.  Differential geometry of curves and surfaces , 1976 .

[20]  J.-M. Leroy,et al.  Calculation of Stresses and Slips in Helical Layers of Dynamically Bent Flexible Pipes , 2001 .

[21]  E. Rabinowicz,et al.  Friction and Wear of Materials , 1966 .

[22]  Qianjin Yue,et al.  Tension behavior prediction of flexible pipelines in shallow water , 2013 .

[23]  J. A. Witz,et al.  On the flexural structural behaviour of flexible pipes, umbilicals and marine cables , 1992 .

[24]  R. H. Knapp.  Helical Wire Stresses in Bent Cables , 1988 .

[25]  S. Sævik,et al.  Theoretical and experimental studies of the axisymmetric behaviour of complex umbilical cross-sections , 2005 .

[26]  Svein Sævik,et al.  A finite element model for predicting stresses and slip in flexible pipe armouring tendons , 1993 .

[27]  C. L. Bournazel,et al.  CALCULATION OF STRESSES AND SLIP IN STRUCTURAL LAYERS OF UNBONDED FLEXIBLE PIPES , 1987 .

[28]  Svein Sævik.  Comparison Between Theoretical and Experimental Flexible Pipe Bending Stresses , 2010 .

[29]  C. Bert,et al.  Theory of wire rope , 1990 .