Modeling of Temperature Distribution in Laser Welding of Lapped Martensitic Steel M1500 and Softening Estimation

[1]  Zhengwei Gu,et al.  Microstructures and Properties of Ultra-high Strength Steel by Laser Welding , 2011 .

[2]  Wei Zhang,et al.  Determination of thermal contact conductance between thin metal sheets of battery tabs , 2014 .

[3]  Stefania Bruschi,et al.  Influence of Temperature and Deformation on Phase Transformation and Vickers Hardness in Tailored Tempering Process: Numerical and Experimental Verifications , 2014 .

[4]  Qing-fu Li,et al.  A Mechanistic Study on the Inhibition of Zinc Behavior During Laser Welding of Galvanized Steel , 2015 .

[5]  S. Muthukumaran,et al.  Simulation of laser butt welding of AISI 316L stainless steel sheet using various heat sources and experimental validation , 2015 .

[6]  Radovan Kovacevic,et al.  Finite-element thermal analysis of laser welding of galvanized high-strength steel in a zero-gap lap joint configuration and its experimental verification , 2012 .

[7]  Mun-Jin Kang,et al.  A study on the CO2 laser welding characteristics of high strength steel up to 1500 MPa for automotive application , 2010 .

[8]  D. A. Scott,et al.  Finite element model of pulsed laser welding , 1999 .

[9]  Majid Bahrami,et al.  Review of Thermal Joint Resistance Models for Nonconforming Rough Surfaces , 2006 .

[10]  Y. Zhou,et al.  Effects of Heat Input and Martensite on HAZ Softening in Laser Welding of Dual Phase Steels , 2008 .

[11]  Chih-Yung Wen,et al.  Experimental study of clamping effects on the performances of a single proton exchange membrane fuel cell and a 10-cell stack , 2009 .

[12]  Jwo Pan,et al.  Failure Mode and Fatigue Behavior of Dissimilar Friction Stir Spot Welds in Lap-Shear Specimens of Transformation-Induced Plasticity Steel and Hot-Stamped Boron Steel Sheets , 2015 .

[13]  E. Bonifaz,et al.  Finite element analysis of heat flow in single-pass arc welds , 2000 .

[14]  C. Qiu,et al.  Strength and Phase Identification of Autogenous Laser Brazed Dissimilar Metal Microjoints , 2015 .

[15]  Antti Salminen,et al.  Fiber Laser Welding of Direct-Quenched Ultrahigh Strength Steels: Evaluation of Hardness, Tensile Strength, and Toughness Properties at Subzero Temperatures , 2015 .

[16]  Panjawat Kongsuwan,et al.  Laser Induced Porosity and Crystallinity Modification of a Bioactive Glass Coating on Titanium Substrates , 2015 .

[17]  Leonardo Orazi,et al.  A Comprehensive Model for Laser Hardening of Carbon Steels , 2013 .

[18]  S. Bruschi,et al.  Numerical modelling of the tailored tempering process applied to 22MnB5 sheets , 2014 .

[19]  Kang Li,et al.  Modeling of temperature field and pool formation during linear laser welding of DP1000 steel , 2014 .

[20]  J. McDermid,et al.  Decoupling of the softening processes during rapid tempering of a martensitic steel , 2014 .

[21]  A. Mistry,et al.  Understanding the Effect of Heat Input and Sheet Gap on Porosity Formation in Fillet Edge and Flange Couch Laser Welding of AC-170PX Aluminum Alloy for Automotive Component Manufacture , 2015 .

[22]  L. Barrallier,et al.  Finite element simulation of magnesium alloys laser beam welding , 2010 .

[23]  Reinhold Kneer,et al.  Determination of thermal contact resistance from transient temperature measurements , 2008 .

[24]  J. Goldak,et al.  A new finite element model for welding heat sources , 1984 .

[25]  M. Avrami.  Kinetics of Phase Change. I General Theory , 1939 .

[26]  J. McDermid,et al.  Softening Kinetics in the Subcritical Heat-Affected Zone of Dual-Phase Steel Welds , 2010 .

[27]  Yung C. Shin,et al.  Predictive modeling of multi-track laser hardening of AISI 4140 steel , 2008 .

[28]  Y. Zhang,et al.  Effect of welding speed on microstructure, hardness and tensile properties in laser welding of advanced high strength steel , 2013 .

[29]  Lin Li,et al.  Coupled Computational Fluid Dynamic and Finite Element Multiphase Modeling of Laser Weld Bead Geometry Formation and Joint Strengths , 2013 .

[31]  Jingjing Li,et al.  Special Issue: Forming and Joining of Lightweight and Multimaterial Systems , 2015 .

[32]  Grant Brandal,et al.  Biocompatibility and Corrosion Response of Laser Joined NiTi to Stainless Steel Wires , 2015 .

[33]  Huanxin Chen,et al.  Influences of temperature and contact pressure on thermal contact resistance at interfaces at cryogenic temperatures , 2012 .

[34]  M. Cooper,et al.  Thermal contact conductance , 1969 .

[35]  F. Goodwin,et al.  Microstructure and fatigue performance of single and multiple linear fiber laser welded DP980 dual-phase steel , 2012 .

[36]  B. Mikic,et al.  THERMAL CONTACT CONDUCTANCE; THEORETICAL CONSIDERATIONS , 1974 .

[37]  Michael F. Ashby,et al.  A second report on diagrams of microstructure and hardness for heat-affected zones in welds , 1984 .

[38]  G. N. Labeas,et al.  Residual stress and distortion calculation of laser beam welding for aluminum lap joints , 2008 .

[39]  J. Embury,et al.  Predicting Transient Softening in the Sub-Critical Heat-Affected Zone of Dual-Phase and Martensitic Steel Welds , 2013 .