Considerations pertaining to the achievement of high burn-ups in HTR fuel

Abstract The satisfactory irradiation performance of coated fuel particles up to burn-ups of, say 10%, has been demonstrated in the past. However, it is shown that some of the most important physical properties of their constituents, which determine this good performance, are only poorly known. This ignorance is likely to become more serious when particles are required to attain higher burn-up values. For example, neutron dose limits above which the anisotropy of the pyrocarbon layers become unacceptably high need to be established. Again, the particle must be designed with adequate voidage to accommodate the gas released by fission, and kernel-coating mechanical interaction must be avoided. Experiments are proposed, in addition to the irradiation and post irradiation examination of particles, which should address these issues. The way this new information can be used in fuel performance codes is discussed, thereby providing a scientific understanding of the behaviour of coated particles—as of interest to researchers, by industry, by utilities and, perhaps most importantly, by regulators.

[1]  David G. Martin.  Some Calculations of the Failure Statistics of Coated Fuel Particles , 1979 .

[2]  J. Bokros,et al.  Neutron-induced charges in crystallinity and thermal conductivity of pyrolytic carbons☆ , 1966 .

[3]  J. Nedderman.  HTGR IS ALIVE AND BEING RELAUNCHED , 1998 .

[4]  Kazuhiro Sawa,et al.  An Investigation of Irradiation Performance of High Burnup HTGR Fuel , 1999 .

[5]  Barry Marsden,et al.  Irradiation Damage in Graphite due to Fast Neutrons in Fission and Fusion Systems , 2000 .

[6]  A. Evans,et al.  Strength of Pyrolytic SiC Coatings of Fuel Particles for High‐Temperature Gas‐Cooled Reactors , 1973 .

[7]  Shusaku Shiozawa,et al.  Development of a Coated Fuel Particle Failure Model under High Burnup Irradiation , 1996 .

[8]  Heinz Nabielek,et al.  Production of carbon monoxide during burn-up of UO2 kerneled HTR fuel particles , 1982 .

[9]  P. A. Tepest.  A direct measurement of Bacon anisotropy factors on pyrocarbon coatings deposited on fuel particles for the high temperature reactor , 1978 .

[10]  H. Bairiot,et al.  Plutonium coated particles development , 1972 .

[11]  J. Kaae.  Effect of irradiation on the mechanical properties of isotropic pyrolytic carbons , 1973 .

[12]  H. Nabielek,et al.  Carbon monoxide formation in UO2 kerneled HTR fuel particles containing oxygen getters , 1986 .

[13]  R. Plunkett,et al.  Formulas for Stress and Strain , 1965 .

[14]  J. Bokros,et al.  Thermal expansivities and preferred orientation of pyrolytic carbons , 1967 .

[15]  J. Turnbull,et al.  Influence of Irradiation Temperature, Burnup, and Fuel Composition on Gas Pressure (Xe, Kr, CO, CO2) in Coated Particle Fuels , 1976 .

[16]  J. Bokros,et al.  Mechanical properties of neutron-irradiated pyrolytic carbons , 1967 .

[17]  H. Walther.  On mathematical models for calculating the mechanical behaviour of coated fuel particles , 1972 .

[18]  K. E. Gilchrist,et al.  Fast neutron induced creep in pyrocarbon under constant stress , 1976 .

[19]  Gregory K. Miller,et al.  Consideration of the effects on fuel particle behavior from shrinkage cracks in the inner pyrocarbon layer , 2001 .

[20]  A. S. Schwartz,et al.  RADIATION-INDUCED DIMENSIONAL CHANGES AND CREEP IN CARBONACEOUS MATERIALS. , 1969 .

[21]  J. Kaae,et al.  Dimensional changes and creep of poorly crystalline isotropic carbons and carbon-silicon alloys during irradiation , 1972 .