Dosimetric characterization of 3D printed bolus at different infill percentage for external photon beam radiotherapy.

BACKGROUND AND PURPOSE 3D printing is rapidly evolving and further assessment of materials and technique is required for clinical applications. We evaluated 3D printed boluses with acrylonitrile butadiene styrene (ABS) and polylactide (PLA) at different infill percentage. MATERIAL AND METHODS A low-cost 3D printer was used. The influence of the air inclusion within the 3D printed boluses was assessed thoroughly both with treatment planning system (TPS) and with physical measurements. For each bolus, two treatment plans were calculated with Monte Carlo algorithm, considering the computed tomography (CT) scan of the 3D printed bolus or modelling the 3D printed bolus as a virtual bolus structure with a homogeneous density. Depth dose measurements were performed with Gafchromic films. RESULTS High infill percentage corresponds to high density and high homogeneity within bolus material. The approximation of the bolus in the TPS as a homogeneous material is satisfying for infill percentages greater than 20%. Measurements performed with PLA boluses are more comparable to the TPS calculated profiles. For boluses printed at 40% and 60% infill, the discrepancies between calculated and measured dose distribution are within 5%. CONCLUSIONS 3D printing technology allows modulating the shift of the build-up region by tuning the infill percentage of the 3D printed bolus in order to improve superficial target coverage.

[1]  Peter E Metcalfe,et al.  Effects on skin dose from unwanted air gaps under bolus in photon beam radiotherapy , 2000 .

[2]  G. D. Bell,et al.  Towards the production of radiotherapy treatment shells on 3D printers using data derived from DICOM CT and MRI: preclinical feasibility studies , 2014, Journal of Radiotherapy in Practice.

[3]  Martijn Kusters,et al.  Clinical implementation of 3D printing in the construction of patient specific bolus for electron beam radiotherapy for non-melanoma skin cancer. , 2016, Radiotherapy and oncology : journal of the European Society for Therapeutic Radiology and Oncology.

[4]  I. Kawrakow.  Accurate condensed history Monte Carlo simulation of electron transport. I. EGSnrc, the new EGS4 version. , 2000, Medical physics.

[5]  Daniel Matias,et al.  Use of a 3D printer to create a bolus for patients undergoing tele-radiotherapy , 2016 .

[6]  J. Adam M. Cunha,et al.  An algorithm for computing customized 3D printed implants with curvature constrained channels for enhancing intracavitary brachytherapy radiation delivery , 2013, 2013 IEEE International Conference on Automation Science and Engineering (CASE).

[7]  Chang Heon Choi,et al.  A Patient-Specific Polylactic Acid Bolus Made by a 3D Printer for Breast Cancer Radiation Therapy , 2016, PloS one.

[8]  Shiqin Su,et al.  Design and production of 3D printed bolus for electron radiation therapy , 2014, Journal of applied clinical medical physics.

[9]  Runqing Jiang,et al.  On bolus for megavoltage photon and electron radiation therapy. , 2013, Medical dosimetry : official journal of the American Association of Medical Dosimetrists.

[10]  Tom Burrows,et al.  Introduction of novel 3D-printed superficial applicators for high-dose-rate skin brachytherapy. , 2017, Brachytherapy.

[11]  Tanya Kairn,et al.  Use of 3D printed materials as tissue-equivalent phantoms , 2015 .

[12]  Ying Xiao,et al.  Impact of dose calculation algorithm on radiation therapy. , 2014, World journal of radiology.

[13]  Ting Chen,et al.  Potential of 3D printing technologies for fabrication of electron bolus and proton compensators , 2015, Journal of applied clinical medical physics.

[14]  J. W. Park,et al.  Three-dimensional customized bolus for intensity-modulated radiotherapy in a patient with Kimura's disease involving the auricle. , 2016, Cancer radiotherapie : journal de la Societe francaise de radiotherapie oncologique.

[15]  Hun-Joo Shin,et al.  A Customized Bolus Produced Using a 3-Dimensional Printer for Radiotherapy , 2014, PloS one.

[16]  Tomas Kron,et al.  The Physics of Radiotherapy X-Rays and Electrons , 2007 .

[17]  Matthew F Bieniosek,et al.  Technical Note: Characterization of custom 3D printed multimodality imaging phantoms. , 2015, Medical physics.

[18]  Allan Rennie,et al.  3D printed facial laser scans for the production of localised radiotherapy treatment masks – A case study , 2016, Journal of visual communication in medicine.

[19]  G. Baroni,et al.  3D-printed applicators for high dose rate brachytherapy: Dosimetric assessment at different infill percentage. , 2016, Physica medica : PM : an international journal devoted to the applications of physics to medicine and biology : official journal of the Italian Association of Biomedical Physics.

[20]  C. Ma,et al.  BEAM: a Monte Carlo code to simulate radiotherapy treatment units. , 1995, Medical physics.

[21]  Rao Khan,et al.  Characterizing 3D printing in the fabrication of variable density phantoms for quality assurance of radiotherapy. , 2016, Physica medica : PM : an international journal devoted to the applications of physics to medicine and biology : official journal of the Italian Association of Biomedical Physics.

[22]  Wazir Muhammad,et al.  Clinical and Dosimetric Implications of Air Gaps between Bolus and Skin Surface during Radiation Therapy , 2013 .

[23]  Tom Depuydt,et al.  Towards 3D printed multifunctional immobilization for proton therapy: Initial materials characterization. , 2016, Medical physics.

[24]  Zhigang Xu,et al.  Use of 3D printers to create a patient‐specific 3D bolus for external beam therapy , 2015, Journal of applied clinical medical physics.

[25]  Wojciech Podraza,et al.  Utilization of a 3D printer to fabricate boluses used for electron therapy of skin lesions of the eye canthi , 2016, Journal of applied clinical medical physics.