EBSD research on the interfacial microstructure of the corrugated Mg/Al laminated material

[1]  H. Nie,et al.  Effect of twins and dynamic recrystallization on the microstructures and mechanical properties of Ti/Al/Mg laminates , 2019, Materials & Design.

[2]  R. Hashemi,et al.  Influence of ARB technique on the microstructural, mechanical and fracture properties of the multilayered Al1050/Al5052 composite reinforced by SiC particles , 2019, Journal of Materials Research and Technology.

[3]  M. Mofid,et al.  Investigating microstructural evolution at the interface of friction stir weld and diffusion bond of Al and Mg alloys , 2019, Journal of Materials Research and Technology.

[4]  J. Han,et al.  Microstructure Characterization and Mechanical Property of Mg/Al Laminated Composite Prepared by the Novel Approach: Corrugated + Flat Rolling (CFR) , 2019, Metals.

[5]  Guoqun Zhao,et al.  Study on Al/Mg/Al sheet fabricated by combination of porthole die co-extrusion and subsequent hot rolling , 2019, Journal of Alloys and Compounds.

[6]  Fei Wang,et al.  A coupled EBSD/TEM study on the interfacial structure of Al/Mg/Al laminates , 2019, Journal of Alloys and Compounds.

[7]  Jian-Huei Feng.  Texture development in the interfacial zone of Al/Cu bimetal cold roll-bonded for E-mobility , 2019, Materials Letters.

[8]  T. Baudin,et al.  Investigation of microstructure and texture evolution of a Mg/Al laminated composite elaborated by accumulative roll bonding , 2019, Materials Characterization.

[9]  Jufu Jiang,et al.  Effect of pass reduction on microstructure, mechanical properties and texture of hot-rolled 7075 alloy , 2019, Materials Characterization.

[10]  M. Jiang,et al.  Unveiling the formation of basal texture variations based on twinning and dynamic recrystallization in AZ31 magnesium alloy during extrusion , 2018, Acta Materialia.

[11]  Zhiquan Huang,et al.  Improvement of magnesium alloy edge cracks by multi-cross rolling , 2018 .

[12]  Jun Zhou,et al.  Deformation behaviors and cyclic strength assessment of AZ31B magnesium alloy based on steady ratcheting effect , 2018 .

[13]  Wei Zhang,et al.  Microstructure evolution and mechanical properties of an AA6061/AZ31B alloy plate fabricated by explosive welding , 2018 .

[14]  S. Reihani,et al.  Al-Mg-Si/SiC laminated composites: Fabrication, architectural characteristics, toughness, damage tolerance, fracture mechanisms , 2017 .

[15]  Guoqun Zhao,et al.  Microstructure analysis of an Al-Zn-Mg alloy during porthole die extrusion based on modeling of constitutive equation and dynamic recrystallization , 2017 .

[16]  H. Jafarian,et al.  Welding parameters analysis and microstructural evolution of dissimilar joints in Al/Bronze processed by friction stir welding and their effect on engineering tensile behavior , 2017 .

[17]  M. R. Jandaghi,et al.  Influence of interfacial adhesion on the damage tolerance of Al6061/SiCp laminated composites , 2017 .

[18]  S. Yokoyama,et al.  Effect of dimple patterning conditions of Periodical Straining Rolling on microstructures and mechanical properties of AZ31 sheets , 2017 .

[19]  T. Langdon,et al.  A comparison of repetitive corrugation and straightening and high-pressure torsion using an Al-Mg-Sc alloy , 2016 .

[20]  H. Nie,et al.  The Microstructure, Texture and Mechanical Properties of the Rolled Al/Mg/Al Clad Sheets , 2016, Journal of Materials Engineering and Performance.

[21]  Fuqian Yang,et al.  Texture Evolution of Single-Pass Hot-Rolled 5052/AZ31/5052 Clad Sheets , 2016 .

[22]  K. A. Padmanabhan,et al.  Effects of die profile on grain refinement in Al–Mg alloy processed by repetitive corrugation and straightening , 2016 .

[23]  Lei Zhang,et al.  Achieving a weak basal texture in a Mg–6Al–3Sn alloy by wave-shaped die rolling , 2015 .

[24]  Jung-Su Kim,et al.  Improvement of interfacial bonding strength in roll-bonded Mg/Al clad sheets through annealing and secondary rolling process , 2015 .

[25]  S. Reihani,et al.  Toughness enhancement in architecturally modified Al6061-5 vol.% SiCp laminated composites , 2015 .

[26]  Wen-xian Wang,et al.  The effect of annealing on the interface microstructure and mechanical characteristics of AZ31B/AA6061 composite plates fabricated by explosive welding , 2015 .

[27]  M. R. Toroghinejad,et al.  Mechanical properties and microstructure evolutions of multilayered Al-Cu composites produced by accumulative roll bonding process and subsequent annealing , 2014 .

[28]  J. Hirsch,et al.  Superior light metals by texture engineering: Optimized aluminum and magnesium alloys for automotive applications , 2013 .

[29]  M. Ma,et al.  Microstructures and mechanical properties of Mg/Mg and Mg/Al/Mg laminated composites prepared via warm roll bonding , 2012 .

[30]  H. D. Manesh,et al.  Bond strength evaluation of roll bonded bi-layer copper alloy strips in different rolling conditions , 2011 .

[31]  M. Mabuchi,et al.  Enhanced stretch formability of Mg–Al–Zn alloy sheets rolled at high temperature (723 K) , 2009 .

[32]  R. Alderliesten,et al.  Damage tolerance assessment by bend and shear tests of two multilayer composites: Glass fibre reinforced metal laminate and aluminium roll-bonded laminate , 2009 .