Thermal cycling evaluation for DFIG wind turbine power converter based on joint modelling

The wind turbine power converter is a critical system component due to relatively higher failure rates compared with the other sub-assemblies. The lifetime of a power device in the converter is closely related to its mean temperature and its variations. In this paper, the power device thermal cycling is analyzed with a multi-physical model developed in PSCAD, which includes detailed doubly-fed induction generator wind turbine modeling, and an electrothermal network of the semiconductors. The power loss obtained from PSCAD is verified with that from the software SemiSel. SemiSel however only shows average temperatures, where as the new model shown here offers much higher fidelity since it can show time-based variation. A discussion and analysis of various methods to implement the electro-thermal model is undertaken. It is shown with the new model that a large temperature swing occurs for the rotor-side converter at the synchronous operating point due to very low frequency currents. This may cause serious stress and uneven heat distributions among the semiconductors. Therefore, working near this point should be avoided during normal operation in order to increase the inverter lifetime. This integrated model can also be used to evaluate the effects of wind speed variations, different power module sizes and cooling systems.

[1]  Cristian Busca.  Modeling lifetime of high power IGBTs in wind power applications - An overview , 2011, 2011 IEEE International Symposium on Industrial Electronics.

[2]  Peter Tavner,et al.  Reliability of wind turbine subassemblies , 2009 .

[3]  U. Drofenik,et al.  A General Scheme for Calculating Switching- and Conduction-Losses of Power Semiconductors in Numerical Circuit Simulations of Power Electronic Systems; International Power Electronics Conference; ; IPEC-Niigata 2005 , 2005 .

[4]  E. Dallago,et al.  Thermal resistance analysis by induced transient (TRAIT) method for power electronic devices thermal characterization. I. Fundamentals and theory , 1998 .

[5]  Peter Tavner,et al.  Condition Monitoring for Device Reliability in Power Electronic Converters: A Review , 2010, IEEE Transactions on Power Electronics.

[6]  Frede Blaabjerg,et al.  Thermal loading and reliability of 10 MW multilevel wind power converter at different wind roughness classes , 2012, ECCE 2012.

[7]  U. Drofenik,et al.  Thermal analysis of a multi-chip Si/SiC-power module for realization of a bridge leg of a 10 kW Vienna rectifier , 2003, The 25th International Telecommunications Energy Conference, 2003. INTELEC '03..

[8]  E. Dallago,et al.  Thermal resistance analysis by induced transient (TRAIT) method for power electronic devices thermal characterization. II. Practice and experiments , 1998 .

[9]  Mahera Musallam,et al.  Impact of different control schemes on the life consumption of power electronic modules for variable speed wind turbines , 2011, Proceedings of the 2011 14th European Conference on Power Electronics and Applications.

[10]  Wilfried Hofmann,et al.  Investigation of doubly-fed induction generator drives behaviour at synchronous operating point in wind turbines , 2009, 2009 13th European Conference on Power Electronics and Applications.

[11]  Mike Barnes,et al.  Doubly-fed induction generator wind turbine modelling for detailed electromagnetic system studies , 2013 .

[12]  M. Liserre,et al.  Power Electronics Converters for Wind Turbine Systems , 2012, IEEE Transactions on Industry Applications.

[13]  Wenyuan Li,et al.  Effect of Wind Speed on Wind Turbine Power Converter Reliability , 2012, IEEE Transactions on Energy Conversion.

[14]  G. Wachutka,et al.  Combination of thermal subsystems modeled by rapid circuit transformation , 2007, 2007 13th International Workshop on Thermal Investigation of ICs and Systems (THERMINIC).

[15]  H. A. Mantooth,et al.  Electro-thermal simulation of an IGBT PWM inverter , 1993, Proceedings of IEEE Power Electronics Specialist Conference - PESC '93.

[16]  Lixiang Wei,et al.  Analysis of IGBT Power Cycling Capabilities Used in Doubly Fed Induction Generator Wind Power System , 2011 .

[17]  A. Mertens,et al.  Steady state lifetime estimation of the power semiconductors in the rotor side converter of a 2 MW DFIG wind turbine via power cycling capability analysis , 2011, Proceedings of the 2011 14th European Conference on Power Electronics and Applications.