Investigation of a novel hybrid process of laser drilling assisted with jet electrochemical machining

Abstract Recast layer and spatter are two inherent defects commonly associated with holes produced with laser drilling. This paper reports a novel hybrid process of laser drilling assisted with jet electrochemical machining (JECM-LD) that aims to minimize such defects and improve the quality of laser-drilled holes. The process based on the application of a jet electrolyte, being aligned coaxially with the focused laser beam, on the workpiece surface during laser drilling. The effect of the jet electrolyte mainly is an electrochemical reaction with materials. The jet electrolyte also cools the workpiece and transports debris during the process. On the basis of a measurement of laser attenuation in electrolyte, an experimental apparatus system is made and JECM-LD experiments have been performed on 0.5-mm-thick 321S20 stainless steel with two lasers at wavelength of 1064 and 532 nm. It is shown that recast layer and spatter have been effectively reduced during the JECM-LD compared with laser drilling in ambient atmosphere conditions.

[1]  E. Arakawa,et al.  Optical Absorption of Liquid Water in the Vacuum Ultraviolet , 1972 .

[2]  Lin Li,et al.  Spatter-free laser percussion drilling of closely spaced array holes , 2001 .

[3]  Lin Li,et al.  The effects of process parameters on spatter deposition in laser percussion drilling , 2000 .

[4]  Wolfgang Schulz,et al.  Laser machining by short and ultrashort pulses, state of the art , 2002 .

[5]  A. Kruusing.  Underwater and water-assisted laser processing: Part 2—Etching, cutting and rarely used methods , 2004 .

[6]  T. I. Quickenden,et al.  Visible and near-ultraviolet absorption spectrum of liquid water. , 1999, Applied optics.

[7]  W. Lau,et al.  Ultrasonic-Aided Laser Drilling of Aluminium-Based Metal Matrix Composites , 1994 .

[8]  B. Yilbas.  Parametric study to improve laser hole drilling process , 1997 .

[9]  M. Jackson,et al.  Laser micro-drilling of tool steel using Nd:YAG lasers , 2003 .

[10]  Arvi Kruusing,et al.  Underwater and water-assisted laser processing: Part 1-general features, steam cleaning and shock processing [review article] , 2004 .

[11]  G. M. Hale,et al.  Optical Constants of Water in the 200-nm to 200-microm Wavelength Region. , 1973, Applied optics.

[12]  K. Baker,et al.  Optical properties of the clearest natural waters (200-800 nm). , 1981, Applied optics.

[13]  Holger Lubatschowski,et al.  Femtosecond Technology for Technical and Medical Applications , 2010 .

[14]  C. Sutcliffe,et al.  Analysis of laser micro drilled holes through aluminium for micro-manufacturing applications , 2005 .

[15]  Lin Li,et al.  Chemical Assisted Laser Machining for The Minimisation of Recast and Heat Affected Zone , 2004 .

[16]  Christopher J. Sutcliffe,et al.  Influence of microsupersonic gas jets on nanosecond laser percussion drilling , 2007 .

[17]  Shrikant V. Joshi,et al.  A statistical approach to determine process parameter impact in Nd : YAG laser drilling of IN718 and Ti-6Al-4V sheets , 2005 .

[18]  P. Corkum,et al.  Influence of laser parameters and material properties on micro drilling with femtosecond laser pulses , 1999 .

[19]  Christopher J. Sutcliffe,et al.  Micromachining of copper using Nd:YAG laser radiation at 1064, 532, and 355 nm wavelengths , 2001 .

[20]  Hendrik Buiteveld,et al.  Optical properties of pure water , 1994, Other Conferences.

[21]  E. Fry,et al.  Absorption spectrum (340-640 nm) of pure water. I. Photothermal measurements. , 1997, Applied optics.