Diurnal Thermal Behavior of Photovoltaic Panel with Phase Change Materials under Different Weather Conditions

The electric power generation efficiency of photovoltaic (PV) panels depends on the solar irradiation flux and the operating temperature of the solar cell. To increase the power generation efficiency of a PV system, this study evaluated the feasibility of phase change materials (PCMs) to reduce the temperature rise of solar cells operating under the climate in Seoul, Korea. For this purpose, two PCMs with different phase change characteristics were prepared and the phase change temperatures and thermal conductivities were compared. The diurnal thermal behavior of PV panels with PCMs under the Seoul climate was evaluated using a 2-D transient thermal analysis program. This paper discusses the heat flow characteristics though the PV cell with PCMs and the effects of the PCM types and macro-packed PCM (MPPCM) methods on the operating temperatures under different weather conditions. Selection of the PCM type was more important than the MMPCM methods when PCMs were used to enhance the performance of PV panels and the mean operating temperature of PV cell and total heat flux from the surface could be reduced by increasing the heat transfer rate through the honeycomb grid steel container for PCMs. Considering the mean operating temperature reduction of 4 °C by PCM in this study, an efficiency improvement of approximately 2% can be estimated under the weather conditions of Seoul.

[1]  Yi Wang,et al.  Preparation, stability and mechanical property of shape-stabilized phase change materials , 2014 .

[2]  J. I. Rosell,et al.  Modelling power output in photovoltaic modules for outdoor operating conditions , 2006 .

[3]  Sandro Nižetić,et al.  Investigation of pork fat as potential novel phase change material for passive cooling applications in photovoltaics , 2018 .

[4]  Philip C. Eames,et al.  Thermal regulation of building-integrated photovoltaics using phase change materials , 2004 .

[5]  Philip C. Eames,et al.  Comparison of a Small Scale 3-d PCM Thermal Control Model with a Validated 2-d PCM Thermal Control Model , 2006 .

[7]  E. Skoplaki,et al.  Operating temperature of photovoltaic modules: A survey of pertinent correlations , 2009 .

[8]  K. Steemers,et al.  Design and overall energy performance of a ventilated photovoltaic façade , 2007 .

[9]  Pascal Henry Biwole,et al.  Improving the Performance of Solar Panels by the Use of Phase-Change Materials , 2011 .

[10]  Agis M. Papadopoulos,et al.  Comprehensive analysis and general economic-environmental evaluation of cooling techniques for photovoltaic panels, Part I: Passive cooling techniques , 2017 .

[11]  Yiannis Tripanagnostopoulos,et al.  Improved PV/T solar collectors with heat extraction by forced or natural air circulation , 2007 .

[12]  E. Skoplaki,et al.  ON THE TEMPERATURE DEPENDENCE OF PHOTOVOLTAIC MODULE ELECTRICAL PERFORMANCE: A REVIEW OF EFFICIENCY/ POWER CORRELATIONS , 2009 .

[13]  Aryadi Suwono,et al.  Improving photovoltaics performance by using yellow petroleum jelly as phase change material , 2016 .

[14]  Ahmad Hasan,et al.  Energy and Cost Saving of a Photovoltaic-Phase Change Materials (PV-PCM) System through Temperature Regulation and Performance Enhancement of Photovoltaics , 2014 .

[15]  B. J. Brinkworth,et al.  Estimation of flow and heat transfer for the design of PV cooling ducts , 2000 .

[16]  E. Radziemska.  The effect of temperature on the power drop in crystalline silicon solar cells , 2003 .

[17]  Małgorzata Jurkowska,et al.  Review on properties of microencapsulated phase change materials slurries (mPCMS) , 2016 .

[18]  K. Emery,et al.  Temperature dependence of photovoltaic cells, modules and systems , 1996, Conference Record of the Twenty Fifth IEEE Photovoltaic Specialists Conference - 1996.

[19]  Yuan Hu,et al.  Effect of expanded graphite on properties of high-density polyethylene/paraffin composite with intumescent flame retardant as a shape-stabilized phase change material , 2010 .

[20]  Y. Tripanagnostopoulos,et al.  Air-cooled PV/T solar collectors with low cost performance improvements , 2007 .

[21]  Seong Jin Chang,et al.  Hygrothermal performance improvement of the Korean wood frame walls using macro-packed phase change materials (MPPCM) , 2017 .

[22]  Brian Norton,et al.  Phase change materials for limiting temperature rise in building integrated photovoltaics , 2006 .

[23]  Yi Wang,et al.  Stearic acid/silica fume composite as form-stable phase change material for thermal energy storage , 2011 .

[24]  Yasser Fathi Nassar,et al.  The reliability of the photovoltaic utilization in southern cities of Libya , 2007 .

[25]  K. Bücher.  Site dependence of the energy collection of PV modules , 1997 .

[26]  Giuseppina Ciulla,et al.  582. A Photovoltaic panel coupled with a phase changing material heat storage system in hot climates , 2008 .