Off-axis conics as base surfaces for freeform optics enable null testability.

When conducting interferometric tests of freeform optical surfaces, additional optical components, such as computer-generated holograms or deformable mirrors, are often necessary to achieve a null or quasi-null. These additional optical components increase both the cost and the difficulty of interferometric tests of freeform optical surfaces. In this paper, designs using off-axis segments of conics as base surfaces for freeforms are explored. These off-axis conics are more complex base surfaces than typically-used base spheres but remain null-testable. By leveraging off-axis conics in conjunction with additional orthogonal polynomial departures, designs were found with up to an order-of-magnitude of improvement in testability estimates relative to designs that use base spheres. Two design studies, a three-mirror telescope and a wide field-of-view four-mirror telescope, demonstrate the impact of using off-axis conics as the base surface.

[1]  Jay Kumler.  Designing and specifying aspheres for manufacturability , 2005, SPIE Optics + Photonics.

[2]  Jose Sasian,et al.  Method for the design of nonaxially symmetric optical systems using free-form surfaces , 2018 .

[3]  G W Forbes.  Manufacturability estimates for optical aspheres. , 2011, Optics express.

[4]  A Cordero-Dávila,et al.  Conic that best fits an off-axis conic section. , 1986, Applied optics.

[5]  Jannick P Rolland,et al.  Degeneracy in freeform surfaces described with orthogonal polynomials. , 2018, Applied optics.

[6]  Fengzhou Fang,et al.  Manufacturing and measurement of freeform optics , 2013 .

[7]  Pengcheng Guo,et al.  Photonic generation and transmission of on–off keying ultra-wideband impulse radio signals over a fiber link utilizing a delay interferometer and a semiconductor optical amplifier , 2018 .

[8]  Jannick P Rolland,et al.  System design of a single-shot reconfigurable null test using a spatial light modulator for freeform metrology. , 2019, Optics letters.

[9]  von F. Zernike.  Beugungstheorie des schneidenver-fahrens und seiner verbesserten form, der phasenkontrastmethode , 1934 .

[10]  Jannick P Rolland,et al.  On-the-fly surface manufacturability constraints for freeform optical design enabled by orthogonal polynomials. , 2019, Optics express.

[11]  Cody B. Kreischer,et al.  Retrace error: interferometry's dark little secret , 2013, Other Conferences.

[12]  J. Wyant,et al.  Computer generated holograms for testing optical elements. , 1971, Applied optics.

[13]  Peter de Groot,et al.  Instantaneous measurement Fizeau interferometer with high spatial resolution , 2011, Optical Engineering + Applications.

[14]  John R. Rogers.  Orthogonal polynomials and tolerancing , 2011, Optical Engineering + Applications.

[15]  Richard N. Youngworth.  Tolerancing Forbes aspheres: advantages of an orthogonal basis , 2009, Optical Engineering + Applications.

[16]  G W Forbes,et al.  Characterizing the shape of freeform optics. , 2012, Optics express.

[17]  Lin Li,et al.  Applying slope constrained Q-type aspheres to develop higher performance lenses. , 2011, Optics express.

[18]  Jannick P Rolland,et al.  Starting geometry creation and design method for freeform optics , 2018, Nature Communications.

[19]  Mary J. Edwards,et al.  Corning's approach to segment blank manufacturing for an extremely large telescope , 2004, SPIE Astronomical Telescopes + Instrumentation.

[20]  Takayuki Nakano,et al.  Configuration of an off-axis three-mirror system focused on compactness and brightness. , 2005, Applied optics.

[21]  Jose M. Sasian.  How to approach the design of a bilateral symmetric optical system , 1994 .

[22]  Bryan D. Stone,et al.  Second-order design methods for definitive studies of plane-symmetric, two-mirror systems , 1994 .

[23]  Dennis Ochse,et al.  Describing freeform surfaces with orthogonal functions , 2015, SPIE Optical Systems Design.

[24]  Jake Bromage,et al.  Gaussian curvature and stigmatic imaging relations for the design of an unobscured reflective relay. , 2018, Optics letters.

[25]  Kate Medicus,et al.  Fabrication of freeform optics , 2015, SPIE Optical Engineering + Applications.

[26]  Kyle Fuerschbach,et al.  Interferometric measurement of a concave, φ-polynomial, Zernike mirror. , 2014, Optics letters.

[27]  J C Wyant,et al.  Using computer generated holograms to test aspheric wavefronts. , 1972, Applied optics.

[28]  Joseph M. Howard,et al.  Starting point designs for freeform four-mirror systems , 2018 .

[29]  Seunghyuk Chang.  Linear astigmatism of confocal off-axis reflective imaging systems with N-conic mirrors and its elimination. , 2015, Journal of the Optical Society of America. A, Optics, image science, and vision.

[30]  K. Thompson,et al.  A new family of optical systems employing φ-polynomial surfaces. , 2011, Optics express.

[31]  K. Thompson,et al.  Theory of aberration fields for general optical systems with freeform surfaces. , 2014, Optics express.