Structured light-based height control for laser metal deposition

[1]  Aitzol Lamikiz,et al.  In-process height control during laser metal deposition based on structured light 3D scanning , 2018 .

[2]  Joshua M. Pearce,et al.  Slicer and process improvements for open-source GMAW-based metal 3-D printing , 2017 .

[3]  Fritz Klocke,et al.  Instantaneous powder flux regulation system for Laser Metal Deposition , 2017 .

[4]  Shaw C. Feng,et al.  A review on measurement science needs for real-time control of additive manufacturing metal powder bed fusion processes , 2017, Int. J. Prod. Res..

[5]  Richard Leach,et al.  Review of in-situ process monitoring and in-situ metrology for metal additive manufacturing , 2016 .

[6]  S. Nowotny,et al.  High performance corrosion resistant coatings by novel coaxial cold- and hot-wire laser cladding methods , 2016 .

[7]  A. Nassar,et al.  ILLUMINATION AND IMAGE PROCESSING FOR REAL-TIME CONTROL OF DIRECTED ENERGY DEPOSITION ADDITIVE MANUFACTURING , 2016 .

[8]  Reinhart Poprawe,et al.  Study of process window development for high deposition-rate laser material deposition by using mixed processing parameters , 2015 .

[9]  Shawn P. Moylan,et al.  Measurement Science Needs for Real-time Control of Additive Manufacturing Powder Bed Fusion Processes , 2015 .

[10]  C. Leyens,et al.  High-performance laser cladding with combined energy sources , 2015 .

[11]  Douglas S. Thomas,et al.  Costs and Cost Effectiveness of Additive Manufacturing , 2014 .

[12]  Gleb A. Turichin,et al.  Investigation and Modeling of the Process of Formation of the Pad Weld and its Microstructure during Laser Cladding by Radiation of High Power Fiber Laser , 2014 .

[13]  Ingomar Kelbassa,et al.  Correlations of Melt Pool Geometry and Process Parameters During Laser Metal Deposition by Coaxial Process Monitoring , 2014 .

[14]  Antti Salminen,et al.  Monitoring and Adaptive Control of Laser Processes , 2014 .

[15]  Christoph Leyens,et al.  Generative Manufacturing and Repair of Metal Parts through Direct Laser Deposition Using Wire Material , 2013, NEW PROLAMAT.

[16]  Andrew C. Brown,et al.  Development of a stereolithography (STL) slicing and G-code generation algorithm for an entry level 3-D printer , 2013, 2013 Africon.

[17]  Sergey N. Grigoriev,et al.  Definition of brightness temperature and restoration of true temperature in laser cladding using infrared camera , 2013 .

[18]  M. Doubenskaia,et al.  Comprehensive analysis of laser cladding by means of optical diagnostics and numerical simulation , 2013 .

[19]  J. Hofman,et al.  A camera based feedback control strategy for the laser cladding process , 2012 .

[20]  Bengt Lennartson,et al.  Height control of laser metal-wire deposition based on iterative learning control and 3D scanning , 2012 .

[21]  Sergey N. Grigoriev,et al.  Optical Monitoring in Laser Cladding of Ti6Al4V , 2012, Journal of Thermal Spray Technology.

[22]  Dichen Li,et al.  The influence of laser and powder defocusing characteristics on the surface quality in laser direct metal deposition , 2012 .

[23]  Lijun Song,et al.  Control of melt pool temperature and deposition height during direct metal deposition process , 2012 .

[24]  J. L. Mato,et al.  FPGA-based measurement of melt pool size in laser cladding systems , 2011, 2011 IEEE International Symposium on Industrial Electronics.

[25]  L. Tang,et al.  Layer-to-Layer Height Control for Laser Metal Deposition Process , 2011 .

[26]  M. Doubenskaia,et al.  Optical Diagnostics of Deposition of Metal Matrix Composites by Laser Cladding , 2011 .

[27]  Y. Taşcıoğlu,et al.  A Method for Slicing CAD Models in Binary STL Format , 2011 .

[28]  Bengt Lennartson,et al.  Increased stability in laser metal wire deposition through feedback from optical measurements , 2010 .

[29]  Alireza Fathi,et al.  Clad height control in laser solid freeform fabrication using a feedforward PID controller , 2007 .

[30]  Reinhart Poprawe,et al.  Development and qualification of a novel laser-cladding head with integrated sensors , 2007 .

[31]  Ehsan Toyserkani,et al.  An image-based feature tracking algorithm for real-time measurement of clad height , 2007, Machine Vision and Applications.

[32]  Reinhart Poprawe,et al.  Identification and qualification of temperature signal for monitoring and control in laser cladding , 2006 .

[33]  Amir Khajepour,et al.  A mechatronics approach to laser powder deposition process , 2006 .

[34]  Jeff Allen,et al.  An Investigation into the Comparative Costs of Additive Manufacture vs. Machine from Solid for Aero Engine Parts , 2006 .

[35]  Duncan P. Hand,et al.  Real-time temperature measurement for process monitoring of laser conduction welding , 2004 .

[36]  Radovan Kovacevic,et al.  Sensing, modeling and control for laser-based additive manufacturing , 2003 .

[37]  R. Kovacevic,et al.  Closed Loop Control of 3D Laser Cladding Based on Infrared Sensing , 2001 .

[38]  Frederic Truchetet,et al.  LASER CLADDING PROCESS AND IMAGE PROCESSING , 1997 .