Stall Inception in a Boundary Layer Ingesting Fan

Jet engines with Boundary Layer Ingestion (BLI) could offer significant reductions in aircraft fuel burn compared with podded turbofans. However, the engine fans must run continuously with severe inlet distortion, which is known to reduce stability. In this paper an experimental study has been completed on a low-speed rig fan operating with a BLI-type inlet distortion. Unsteady casing static pressure measurements have been made at multiple locations during stall events. Steady-state, full-annulus area traverses have also been performed at rotor inlet and exit at a near-stall operating point. The reduction in stability caused by BLI is found to be small. It is found that with BLI the fan can operate stably despite the presence of localised regions where the rotor operating point lies beyond the stability boundary measured in clean flow. With the BLI-type distortion applied, the measured rotor incidence varies around the annulus due to non-uniform upstream velocity and swirl. The measured amplitude of unsteady casing pressure fluctuations just prior to stall is found to correlate with the circumferential variation of rotor incidence, suggesting that rotor incidence is a key variable affecting the creation and growth of flow disturbances. In regions of high incidence, disturbances resembling local flow separations are initiated. However, in regions of low or negative incidence, any disturbances decay rapidly. Full rotating stall with BLI occurs when high incidence regions are widespread enough to sustain disturbances which can propagate around the entire annulus.Copyright © 2015 by ASME

[1]  Cesare A. Hall,et al.  Aerodynamics of Boundary Layer Ingesting Fans , 2014 .

[2]  J. P. Longley.  Measured and Predicted Effects of Inlet Distortion on Axial Compressors , 1990 .

[3]  H. Pearson,et al.  Wakes in Axial Compressors , 1959 .

[4]  Gerald V. Brown,et al.  Turboelectric Distributed Propulsion in a Hybrid Wing Body Aircraft , 2011 .

[5]  J. P. Longley,et al.  Inlet distortion effects in aircraft propulsion system integration , 1992 .

[6]  Ivor Day,et al.  Stall Inception in Axial Flow Compressors , 1991 .

[7]  C. Reid,et al.  The Response of Axial Flow Compressors to Intake Flow Distortion , 1969 .

[8]  Ivor Day,et al.  Detailed Measurements of Spike Formation in an Axial Compressor , 2012 .

[9]  D. D. Williams,et al.  Review of current knowledge on engine response to distorted inflow conditions , 1987 .

[10]  James I. Hileman,et al.  Assessment of Technologies for the Silent Aircraft Initiative , 2009 .

[11]  Cesare A. Hall,et al.  A Study of Fan-Distortion Interaction Within the NASA Rotor 67 Transonic Stage , 2010 .

[12]  Graham Pullan,et al.  Stall Warning by Blade Pressure Signature Analysis , 2011 .

[13]  Scott C. Morris,et al.  An Experimental and Computational Investigation of Tip Clearance Flow and Its Impact on Stall Inception , 2010 .

[14]  Masahiro Inoue,et al.  Comparative studies on short and long length-scale stall cell propagating in an axial compressor rotor , 2000 .

[15]  Graham Pullan,et al.  Origins and structure of spike-type rotating stall , 2012 .

[16]  A. M. Pradeep,et al.  Investigations on the Effect of Inflow Distortion on the Performance of a High Aspect Ratio, Low Speed Contra Rotating Fan Stage , 2013 .

[17]  Mark Drela,et al.  Preliminary Experimental Assessment of the Boundary Layer Ingestion Benefit for the D8 Aircraft , 2014 .

[18]  Tom Hynes,et al.  Stall Inception in Axial Compressors , 1989 .

[19]  E. Greitzer,et al.  A Method for Assessing Effects of Circumferential Flow Distortion on Compressor Stability , 1987 .

[20]  Tom Hynes,et al.  Boundary Layer Ingesting Intakes: Design and Optimization , 2009 .

[21]  Razvan Virgil Florea,et al.  Aerodynamic Analysis of a Boundary-Layer-Ingesting Distortion-Tolerant Fan , 2013 .

[22]  Paul G. Tucker,et al.  The Effect of Inlet Guide Vanes on Inlet Flow Distortion Transfer and Transonic Fan Stability , 2013 .

[23]  Leroy H. Smith.  Wake ingestion propulsion benefit , 1993 .