Enhancement of pure hydrogen production through the use of a membrane reactor

Abstract Pure hydrogen production is of great interest as it is an energy carrier which can be used in PEM fuel cells for power production. Methane Steam Reforming (MSR) is commonly used for hydrogen production although the produced hydrogen is not free of other components. Membrane Reactors (MR) enable a pure hydrogen product stream and allows the reaction to take place at significantly lower temperatures (lower than 550 °C) than in conventional reactors (greater than 800 °C) with comparable methane conversion. This is achieved by hydrogen removal through a permselective Pd–Ag based membrane that cause a favorable shift in chemical equilibrium towards hydrogen production. In the present study, a two-dimensional, nonlinear, and pseudo-homogeneous mathematical model of a catalytic fixed-bed membrane reactor for methane steam reforming over a nickel-based foam supported catalyst is presented. Simulated results referring to the distribution of species, methane conversion, temperature and hydrogen flowrate along the reactor for different radial positions are obtained and analyzed. The performance of structured catalyst and catalyst supported on foam configurations under the same operating conditions is also studied. Experimental results for the membrane facilitate the identification of suitable operating conditions.

[1]  Spyros Voutetakis,et al.  Catalytic Partial Oxidation of Methane in a Spouted Bed Reactor. Design of a Pilot Plant Unit and Optimization of Operating Conditions. , 1998 .

[2]  J. Richardson,et al.  Properties of ceramic foam catalyst supports: pressure drop , 2000 .

[3]  Enrico Drioli,et al.  Effect of energy transport on a palladium-based membrane reactor for methane steam reforming process , 2001 .

[4]  Fabiano A.N. Fernandes,et al.  Methane steam reforming modeling in a palladium membrane reactor , 2006 .

[5]  G. Manzolini,et al.  H2 production by low pressure methane steam reforming in a Pd–Ag membrane reactor over a Ni-based catalyst: Experimental and modeling , 2010 .

[6]  Shigeyuki Uemiya,et al.  Steam reforming of methane in membrane reactors: comparison of electroless-plating and CVD membranes and catalyst packing modes , 2000 .

[7]  Martyn V. Twigg,et al.  Fundamentals and applications of structured ceramic foam catalysts , 2007 .

[8]  L. Marrelli,et al.  Reformer and membrane modules plant powered by a nuclear reactor or by a solar heated molten salts: Assessment of the design variables and production cost evaluation , 2008 .

[9]  G. Froment,et al.  Modeling of Dual-Zone Structured Reactors for Natural Gas Steam Reforming , 2013 .

[10]  Aydin K. Sunol,et al.  Modeling and simulation of methane steam reforming in a thermally coupled membrane reactor , 2007 .

[11]  Bernard P. A. Grandjean,et al.  Methane steam reforming in asymmetric Pd- and Pd-Ag/porous SS membrane reactors , 1994 .

[12]  G. Froment,et al.  Methane steam reforming, methanation and water‐gas shift: I. Intrinsic kinetics , 1989 .

[13]  S. Tosti,et al.  Experimental and modeling studies on the low-temperature water-gas shift reaction in a dense Pd―Ag packed-bed membrane reactor , 2011 .

[14]  Akira Endo,et al.  Simulation of a Porous Ceramic Membrane Reactor for Hydrogen Production , 2005 .

[15]  Alberto Giaconia,et al.  Life Cycle Assessment of a High Temperature Molten Salt Concentrated Solar Power Plant , 2011 .

[16]  P. Seferlis,et al.  Modeling and Simulation of a Membrane Reactor for the Low Temperature Methane Steam Reforming , 2013 .

[17]  R. Dittmeyer,et al.  Methane steam reforming operation and thermal stability of new porous metal supported tubular palladium composite membranes , 2013 .

[18]  M. De Falco,et al.  Simulation of large-scale membrane reformers by a two-dimensional model , 2007 .

[19]  Spyros Voutetakis,et al.  Catalytic partial oxidation of methane to synthesis gas in a pilot-plant-scale spouted-bed reactor , 1999 .

[20]  Bernard P. A. Grandjean,et al.  Catalytic palladium‐based membrane reactors: A review , 1991 .

[21]  R. Hughes,et al.  A simulative comparison of dense and microporous membrane reactors for the steam reforming of methane , 1998 .

[22]  L. D. Paola,et al.  Methane membrane steam reforming: Heat duty assessment , 2014 .

[23]  J. Richardson,et al.  Properties of ceramic foam catalyst supports: mass and heat transfer , 2003 .

[24]  D. Simakov,et al.  Design of a thermally balanced membrane reformer for hydrogen production , 2008 .

[25]  D. Jansen,et al.  Towards application of palladium membrane reactors in large scale production of hydrogen , 2009 .

[26]  Jam Hans Kuipers,et al.  Modelling of packed bed membrane reactors for autothermal production of ultrapure hydrogen , 2006 .

[27]  Fausto Gallucci,et al.  A simulation study of the steam reforming of methane in a dense tubular membrane reactor , 2004 .

[28]  M. De Falco,et al.  Heat transfer and hydrogen permeability in modelling industrial membrane reactors for methane steam reforming , 2007 .

[29]  Haitao Liu,et al.  Catalytic performance of novel Ni catalysts supported on SiC monolithic foam in carbon dioxide reforming of methane to synthesis gas , 2008 .

[30]  V. Palma,et al.  Methane auto-thermal reforming on honeycomb and foam structured catalysts: The role of the support on system performances , 2013 .