Critical assessment of pile modulus determination methods

The elastic modulus of a concrete pile is an important parameter for the interpretation of load test results. This paper summarizes and assesses the methods available for its determination. Ten methods have been identified of which four are based on laboratory tests and the remainder on in situ pile instrumentation. Six of the methods have been used to interpret the modulus of a concrete pile subject to an axial load test. From the analyses, it was found that creep strains that developed during load-holding periods can have a significant effect on the modulus value if not allowed for when assessing the measured strain values. Based on a comparison of the derived pile loads the secant modulus method was found to be the most satisfactory. The tangent modulus method was also found to be a useful tool for investigating the effect of a partial steel casing — a feature of the method that has not been discussed before. Surprisingly, the theoretically correct transformed area equation had the worst performance, p...

[1]  Bengt H. Fellenius,et al.  Long-Term Monitoring of Strain in Instrumented Piles , 2009 .

[2]  Michael Brown,et al.  Analysis of a rapid load test on an instrumented bored pile in clay , 2006 .

[3]  Chanakya Arya,et al.  Eurocodes 2: Design of concrete structures , 2009 .

[4]  Scott Webster,et al.  BEHAVIOR OF CYLINDER PILES DURING PILE INSTALLATION , 2007 .

[5]  L C Reese,et al.  DRILLED SHAFTS: CONSTRUCTION PROCEDURES AND DESIGN METHODS , 1999 .

[6]  Bujang B. K. Huat,et al.  Pile Instrumentation Using Retrievable Sensors , 2008 .

[7]  S. Timoshenko,et al.  Theory of elasticity , 1975 .

[8]  E. Dibiagio,et al.  Load tests on friction piles in loose sand : Conference. Session three. 11F, 3T, 2R. PROC. EIGHTH INT. CONF. ON SOIL MECH. FOUND. ENGNG, MOSCOW, 1973, V2.1, 1973, P109–117 , 1975 .

[9]  Jbc Taylor,et al.  Measurement of stress in concrete , 1955 .

[10]  Lidija Zdravković,et al.  The influence of partial soil saturation on pile behaviour , 2003 .

[11]  Bengt H. Fellenius,et al.  From Strain Measurements to Load in an Instrumented Pile , 2001 .

[12]  R. Finno,et al.  Load Transfer Characteristics of Micropiles in Dolomite , 2002 .

[13]  J. Omer,et al.  Instrumented load tests in mudstone: pile capacity and settlement prediction , 2002 .

[14]  Bengt H. Fellenius,et al.  Determining the Resistance Distribution in Piles Part 1. Notes on Shift of No-Load Reading and Residual Load , 2002 .

[15]  Hs Lacy.  Load Testing of Instrumented 225-Foot-Long Prestressed Concrete Piles , 1979 .

[16]  Jack P. Moehle,et al.  "BUILDING CODE REQUIREMENTS FOR STRUCTURAL CONCRETE (ACI 318-11) AND COMMENTARY" , 2011 .

[17]  Phillip S. K. Ooi,et al.  Numerical Study of an Integral Abutment Bridge Supported on Drilled Shafts , 2010 .

[18]  B H Fellenius.  THE ANALYSIS OF RESULTS FROM ROUTINE PILE LOAD TESTS , 1980 .

[19]  G. Mullins,et al.  Concrete stress determination in Rapid Load Tests , 2008 .

[20]  C. Medaglia,et al.  A Numerical Study , 2005 .

[21]  M England,et al.  REVIEW OF FOUNDATION TESTING METHODS AND PROCEDURES. , 1994 .

[22]  W. G. K. Fleming.  A new method for single pile settlement prediction and analysis , 1992 .

[23]  M J Tomlinson,et al.  FOUNDATION DESIGN AND CONSTRUCTION. 6TH EDITION , 1995 .

[24]  Bengt H. Fellenius,et al.  Tangent Modulus of Piles Determined from Strain Data , 1989 .

[25]  James G. MacGregor,et al.  Reinforced Concrete: Mechanics and Design , 1996 .

[26]  John Dunnicliff,et al.  Geotechnical Instrumentation for Monitoring Field Performance , 1988 .

[27]  Jack Hayes,et al.  INTERPRETING STRAIN MEASUREMENTS FROM LOAD TESTS IN BORED PILES , 2002 .

[28]  S. Timoshenko,et al.  Theory of Elasticity (3rd ed.) , 1970 .