Installed performance evaluation of an air turbo-rocket expander engine

Abstract The propulsion plant of a prospective supersonic cruise aircraft consists of an air turbo-rocket expander and a dual-mode ramjet. A comprehensive numerical model was constructed to examine the performance of the air turbo-rocket during the supersonic acceleration of the vehicle. The numerical model comprised a one-dimensional representation of the fluid paths through the dual-mode ramjet, the air turbo-rocket combustor, the regenerator and the airframe-integrated nozzle, whereas the turbomachinery and the air turbo-rocket bypass were included as zero-dimensional models. The intake operation was based on the results of time-averaged Euler simulations. A preliminary engine analysis revealed that the installation effects restricted significantly the operational envelope, which was subsequently extended bypassing the air turbo-rocket. Hence the engine was throttled varying the mixture ratio and the fan compression ratio. Nevertheless, the performance was optimal when the demand from the air turbo-rocket matched the intake air flow capture. The heat recovery across the regenerator was found critical for the operation of the turbomachinery at low speed. The transition of the air turbo-rocket to ramjet operation was identified at Mach 4.5. During this regime, the propulsion plant was rather insensitive to the mixture ratio and was throttled with the air turbo-rocket throat area.

[1]  John A. Bossard,et al.  The influence of turbomachinery characteristics on air turbo rocket engine operation , 2000 .

[2]  M. Omizo,et al.  Modeling , 1983, Encyclopedic Dictionary of Archaeology.

[3]  G. Paniagua,et al.  Modeling, Analysis, and Optimization of theAir-Turborocket Expander Engine , 2013 .

[4]  Stuart W. Churchill,et al.  A general expression for the correlation of rates of transfer and other phenomena , 1972 .

[5]  V. V. Kozlaykov System analysis of jet engines of high supersonic flight velocities , 1997 .

[6]  Nobuhiro Tanatsugu,et al.  Thermal design of a hydrogen heater for an air turboramjet engine , 1995 .

[7]  M. Martinez-Sanchez Liquid rocket propulsion theory , 1993 .

[8]  Oliver Knab,et al.  Advanced Cooling Circuit Layout for the VINCI Expander Cycle Thrust Chamber , 2002 .

[9]  H. Seifert,et al.  Rocket Propulsion Elements , 1963 .

[10]  Tom Verstraete,et al.  Integrated multifidelity, multidisciplinary evolutionary design optimization of counterrotating compressors , 2014, Integr. Comput. Aided Eng..

[11]  Jörg Riccius,et al.  Development of Technologies for a CMC-based Combustion Chamber , 2009 .

[12]  Johan Steelant,et al.  Numerical Simulations of the LAPCAT-MR2 Vehicle Scramjet Engine , 2013 .

[13]  A. Bejan,et al.  Heat transfer handbook , 2003 .

[14]  Yang Tao,et al.  Quasi-continuous high-order sliding mode controller and observer design for flexible hypersonic vehicle☆ , 2013 .

[15]  Johan Steelant,et al.  Preliminary Design of the Low Speed Propulsion Air Intake of the LAPCAT-MR2 Aircraft , 2011 .

[16]  Johan Steelant Sustained Hypersonic Flight in Europe: First Technology Achievements within LAPCAT II , 2011 .

[17]  G. G. Stokes "J." , 1890, The New Yale Book of Quotations.

[18]  Johan Steelant,et al.  Combustor and Material Integration for high speed aircraft in the European research Program ATLLAS2. , 2014 .

[19]  Christoph Kirchberger,et al.  Improved Prediction of Heat Transfer in a Rocket Combustor for GOX/Kerosene , 2009 .

[20]  Gerald Hagemann,et al.  Advanced Rocket Nozzles. , 1998 .

[21]  N. C Bissinger,et al.  Improvement of forebody/inlet integration for hypersonic vehicle , 1998 .

[22]  W. B. LITTLER,et al.  Rocket Propulsion , 1959, Nature.

[23]  Guillermo Paniagua,et al.  Modeling, Analysis and Optimization of the Air-Turborocket Expander Engine , 2012 .

[24]  William H. Heiser,et al.  Hypersonic Airbreathing Propulsion , 1994 .

[25]  D. R. Bartz Turbulent Boundary-Layer Heat Transfer from Rapidly Accelerating Flow of Rocket Combustion Gases and of Heated Air , 1965 .

[26]  J. Steelant,et al.  Preliminary Performance Analysis of the LAPCAT-MR2 by means of Nose-to-Tail Computations , 2012 .

[27]  J. Moral,et al.  ESPSS Simulation Platform , 2010 .

[28]  Von Karman,et al.  CADO : a Computer Aided Design and Optimization Tool for Turbomachinery Applications , 2010 .

[29]  Francesco Di Matteo,et al.  Start-Up Transient Simulation of a Liquid Rocket Engine , 2011 .