Mechanical Behavior of Thru-air Bonded Nonwoven Structures

Thermally bonded structures are amongst the most widely used nonwoven structures, with applications ranging from baby diapers to high performance geotextiles. These structures undergo various modes of deformation during their performance. In this study, the mechanical properties namely, tension, shear, bending and compression of thermal bonded polyester fabrics, have been investigated, including directional dependence of the tensile and bending tests, revealing anisotropic characteristics. In addition, the fiber orientation distribution was determined using two-dimensional (2D) image analysis of fabric cross-sections, a technique that is generally used for measuring fiber orientation in short-fiber reinforced composites. The ambiguities, errors and corrections employed in the measurements of fiber orientation are discussed. The initial tensile response of thermal bonded nonwovens has been predicted and compared with the experimental stress-strain curves obtained in various test directions. Bending and compression measurements were done on KES-F and shear measurements were carried out using picture frame test up to a shear angle of 45°.

[1]  Norman B. Beil,et al.  Modeling and Computer Simulation of the Compressional Behavior of Fiber Assemblies , 2002 .

[2]  Stanley Backer,et al.  Some Principles of Nonwoven Fabrics1 , 1960 .

[3]  T. Komori,et al.  Numbers of Fiber-to-Fiber Contacts in General Fiber Assemblies , 1977 .

[4]  H. S. Kim,et al.  Anisotropy in the Mechanical Properties of Thermally Spot-Bonded Nonwovens: Experimental Observations , 2001 .

[5]  Takashi Komori,et al.  Estimation of Fiber Orientation and Length in Fiber Assemblies , 1978 .

[6]  Norman B. Beil,et al.  Modeling and Computer Simulation of the Compressional Behavior of Fiber Assemblies , 2002 .

[7]  Ignace Verpoest,et al.  Picture Frame Test of Woven Composite Reinforcements with a Full-Field Strain Registration , 2006 .

[8]  Michel Vincent,et al.  Fibre-orientation measurements in short-glass-fibre composites—II: a quantitative error estimate of the 2D image analysis technique , 2001 .

[9]  S. Lomov,et al.  Anisotropy of fabrics and fusible interlinings , 1998 .

[10]  Ning Pan,et al.  A Modified Analysis of the Microstructural Characteristics of General Fiber Assemblies , 1993 .

[11]  N. Pan,et al.  Theory of the Compression Hysteresis of Fibrous Assemblies , 1989 .

[12]  S. Batra,et al.  Influence of Fiber Structure on Properties of Thermally Point Bonded Polypropylene Nonwovens , 1999 .

[13]  Julie Chen,et al.  Micromechanics of a Planar Hybrid Fibrous Network1 , 1997 .

[14]  Yuris A. Dzenis,et al.  Elasticity of planar fiber networks , 2005 .

[15]  J. Hearle,et al.  Studies in Nonwoven Fabrics , 1964 .

[16]  Takashi Komori,et al.  Theory of the General Deformation of Fiber Assemblies , 1991 .

[17]  Behnam Pourdeyhimi,et al.  Review of Thermally Point-Bonded Nonwovens: Materials, Processes, and Properties , 2006 .

[18]  Thermally bonded nonwoven filters composed of bicomponent polypropylene/polyester fiber: I. Statistical approach for minimizing the pore size. , 2006 .

[19]  C. M. van Wyk,et al.  20—NOTE ON THE COMPRESSIBILITY OF WOOL , 1946 .

[20]  N. Pan,et al.  Theory of the Shear Deformation of Fibrous Assemblies , 1989 .

[21]  G. Zak,et al.  Estimation of Three-Dimensional Fibre-Orientation Distribution in Short-Fibre Composites by a Two-Section Method , 2001 .

[22]  Jia-Horng Lin,et al.  Effect of Fiber Arrangement on the Mechanical Properties of Thermally Bonded Nonwoven Fabrics , 2003 .

[23]  Amit Rawal.  A Modified Micromechanical Model for the Prediction of Tensile Behavior of Nonwoven Structures , 2006 .