The effect of monolayer TiCN-, AlTiN-, TiAlN-and two layers TiCN + TiN- and AlTiN + TiN-coated cutting tools on tool wear, cutting force, surface roughness and chip morphology during high-speed milling of Ti6Al4V titanium alloy
暂无分享,去创建一个
[1] Ming Chen,et al. WEAR MECHANISMS AND PERFORMANCE OF COATED INSERTS DURING FACE MILLING OF TC11 AND TC17 ALLOYS , 2013 .
[2] M. Nouari,et al. Wear characteristics and performance of multi-layer CVD-coated alloyed carbide tool in dry end milling of titanium alloy , 2006 .
[3] E. Kuram,et al. Effects of blended vegetable‐based cutting fluids with extreme pressure on tool wear and force components in turning of Al 7075‐T6 , 2013 .
[4] Ming Chen,et al. Experimental investigation on hard milling of high strength steel using PVD-AlTiN coated cemented carbide tool , 2014 .
[5] Matthew S. Dargusch,et al. Tool life and wear mechanisms in laser assisted milling Ti-6Al-4V , 2015 .
[6] S. Veldhuis,et al. Wear behavior of adaptive nano-multilayered AlTiN/MexN PVD coatings during machining of aerospace alloys , 2010 .
[7] S. Turchetta,et al. Cutting force, tool life and surface integrity in milling of titanium alloy Ti-6Al-4V with coated carbide tools , 2016 .
[8] Yuebin B. Guo,et al. A new multi-view approach to characterize 3D chip morphology and properties in end milling titanium Ti-6Al-4V , 2008 .
[9] Babur Ozcelik,et al. Experimental investigations of vegetable based cutting fluids with extreme pressure during turning of AISI 304L , 2011 .
[10] Jun Zhao,et al. Performance evaluation of ultra-fine grain carbide in high-speed milling of Ti-6Al-4V , 2014 .
[11] Paul Mativenga,et al. Evaluation and selection of hard coatings for micro milling of hardened tool steel , 2008 .
[12] D. Reynaerts,et al. Process investigation on meso-scale hard milling of ZrO2 by diamond coated tools , 2014 .
[13] Z. Qin,et al. Tool wear characteristics in high-speed milling of graphite using a coated carbide micro endmill , 2009 .
[14] L. N. López de Lacalle,et al. Advanced cutting conditions for the milling of aeronautical alloys , 2000 .
[15] Wei Zhou,et al. Influence of cutting speed on cutting force, flank temperature, and tool wear in end milling of Ti-6Al-4V alloy , 2014 .
[16] M. Nouari,et al. Experimental investigation on the effect of the material microstructure on tool wear when machining hard titanium alloys: Ti–6Al–4V and Ti-555 , 2013 .
[17] Denni Kurniawan,et al. Cutting Force and Surface Roughness Characterization in Cryogenic High-Speed End Milling of Ti–6Al-4V ELI , 2014 .
[18] Taylan Altan,et al. High-speed machining of cast iron and alloy steels for die and mold manufacturing , 2000 .
[19] S. Veldhuis,et al. Design and performance of AlTiN and TiAlCrN PVD coatings for machining of hard to cut materials , 2009 .
[20] Weiwei Ming,et al. Evaluation of the performance of coated carbide tools in face milling TC6 alloy under dry condition , 2013 .
[21] Paul Mativenga,et al. Wear and cutting forces in high-speed machining of H13 using physical vapour deposition coated carbide tools , 2005 .
[22] S. Ding,et al. Experimental investigation of end milling of titanium alloys with polycrystalline diamond tools , 2014 .
[23] Qing Long An,et al. An experimental investigation on effects of minimum quantity lubrication oil supply rate in high-speed end milling of Ti–6Al–4V , 2012 .
[24] H. Çalışkan,et al. The effect of aCN/TiAlN coating on tool wear, cutting force, surface finish and chip morphology in face milling of Ti6Al4V superalloy , 2015 .
[25] P. Mativenga,et al. Wear mechanism analysis in milling of Ti-6Al-4V alloy , 2013 .
[26] Wong Yoke San,et al. An empirical study on the characterization of machined surface integrity by chip morphology in dry end-milling of titanium alloy , 2014 .
[27] G. D'Errico,et al. A study of coatings for end mills in high speed metal cutting , 1999 .
[28] S. Palanisamy,et al. Effect of cryogenic compressed air on the evolution of cutting force and tool wear during machining of Ti-6Al-4V alloy , 2015 .
[29] Jun Zhao,et al. Cutting forces and tool failure in high-speed milling of titanium alloy TC21 with coated carbide tools , 2015 .
[30] S. Sharif,et al. Evaluation of wear mechanisms of coated carbide tools when face milling titanium alloy , 2000 .
[31] A. Jawaid,et al. Tool wear characteristics in turning of titanium alloy Ti-6246 , 1999 .
[32] Z. M. Wang,et al. Performance of PVD-Coated Carbide Tools When Machining Ti-6Al-4V© , 1997 .
[33] Álisson Rocha Machado,et al. Performance of cutting fluids during face milling of steels , 2001 .
[34] Haslina Arshad,et al. Performance of alloyed uncoated and CVD-coated carbide tools in dry milling of titanium alloy Ti-6242S , 2007 .
[35] XiaoQi Chen,et al. An experimental study of tool wear and cutting force variation in the end milling of Inconel 718 with coated carbide inserts , 2006 .
[36] A. F. Ismail,et al. Effectiveness of uncoated WC–Co and PCD inserts in end milling of titanium alloy—Ti–6Al–4V , 2007 .
[37] Jun Zhao,et al. Progressive tool failure in high-speed dry milling of Ti-6Al-4V alloy with coated carbide tools , 2012 .
[38] Babur Ozcelik,et al. The effect of extreme pressure added vegetable based cutting fluids on cutting performance in milling , 2013 .
[39] Paul Mativenga,et al. An Investigation of Tool Chip Contact Phenomena in High-Speed Turning Using Coated Tools , 2006 .