Hysteretic performance of circular hollow section tubular joints with collar-plate reinforcement

Abstract Welded tubular joints have a weak stiffness in the chord radial direction due to the hollow section, and failure frequently occurs mostly on the chord surface along the weld toe. In the past, collar-plate has been proven to be effective in improving the stiffness and thus increasing the load carrying capacity of a tubular joint. This paper reports the results of a further study on investigating the effect of collar-plate reinforcement on the hysteretic behavior of a welded tubular joint. Overall, a total of 4 tubular T-joints with collar-plate reinforcement together with 4 corresponding un-reinforced specimens are studied experimentally. In the experimental tests, quasi-static axial cyclic loading is applied to these specimens. The hysteretic performance of the reinforced and un-reinforced T-joint specimens is then evaluated from the hysteretic curves, ductility and the energy dissipation ratio etc. Based on the experimental results, it is found that the T-joint specimens with collar-plate reinforcement can dissipate more energy before failure when they are subjected to cyclic loading compared to the un-reinforced ones, and thus they have a more ductile characteristic. Such ductility is attributed to the improved deformed capacity as well as the increased load carrying capacity of the reinforced T-joints.

[1]  S. P. Chiew,et al.  Static Strength of Tubular T-Joints with Reinforced Chord under Axial Compression , 2010 .

[2]  T. C. Fung,et al.  Ultimate Capacity of Doubler Plate–Reinforced Tubular Joints , 1999 .

[3]  Shao Yong-bo.  Study on Reinforcing Methods for Welded Tubular Joints Structures , 2009 .

[4]  Yoo Sang Choo,et al.  Static strength of collar plate reinforced CHS X-joints loaded by in-plane bending , 2004 .

[5]  William J.T. Daniel,et al.  Parametric Study of Hot Spot Stresses around Tubular Joints with Doubler Plates , 2007 .

[6]  Ai Kah Soh,et al.  Experimental investigation of a doubler-plate reinforced tubular T-joint subjected to combined loadings , 2001 .

[7]  Wei Wang,et al.  Hysteretic behaviour of tubular joints under cyclic loading , 2007 .

[8]  A. Llewelyn-Parry,et al.  Offshore Tubular T-Joints Reinforced with Internal Plain Annular Ring Stiffeners , 2004 .

[9]  Yoo Sang Choo,et al.  Static Strength of T-Joints Reinforced with Doubler or Collar Plates. I: Experimental Investigations , 2005 .

[10]  Yoo Sang Choo.  Recent Development and Innovation in Tubular Structures , 2005 .

[11]  Yue Yin,et al.  Experimental Study on hysteretic behaviour of tubular N-joints , 2009 .

[12]  Zhenghua Cao,et al.  Experimental and numerical analysis of fatigue behaviour for tubular K-joints , 2005 .

[13]  Chee Kiong Soh,et al.  Hysteretic behavior of completely overlap tubular joints , 2001 .

[14]  T. C. Fung,et al.  Behavior of Completely Overlapped Tubular Joints under Cyclic Loading , 2001 .

[15]  Marcus M. K. Lee,et al.  Strength prediction for ring-stiffened DT-joints in offshore jacket structures , 2005 .

[16]  Seng-Tjhen Lie,et al.  Fatigue Performance of Cracked Tubular T Joints under Combined Loads. II: Numerical , 2004 .

[17]  D. S. Ramachandra Murthy,et al.  Fatigue Behavior of Internally Ring-Stiffened Welded Steel Tubular Joints , 2000 .

[18]  Alain Nussbaumer,et al.  Experimental study on the fatigue behaviour of welded tubular K-joints for bridges , 2006 .

[19]  Yoo Sang Choo,et al.  STATIC STRENGTH OF T-JOINTS REINFORCED WITH DOUBLER OR COLLAR PLATES. II: NUMERICAL SIMULATIONS , 2005 .