New Paradigm in Control of Machining System’s Dynamics

The increasing demands for precision and efficiency in machining call for effective control strategies based on the identification of static and dynamic characteristics under operational conditions ...

[1]  N. Kalouptsidis,et al.  Spectral analysis , 1993 .

[2]  Andreas Archenti,et al.  A Computational Framework for Control of Machining System Capability : From Formulation to Implementation , 2011 .

[3]  Yusuf Altintas,et al.  Chatter Stability in Turning and Milling with in Process Identified Process Damping , 2010 .

[4]  S. Smith,et al.  Stabilizing chatter by automatic spindle speed regulation , 1992 .

[5]  A. Kras,et al.  Amplified Piezo Actuator APA® with viscoelastic material for machine tool semi-active damping system , 2014 .

[6]  J. Tlusty,et al.  Stability Lobes in Milling , 1983 .

[7]  P. Paultre,et al.  Modal identification based on the time–frequency domain decomposition of unknown-input dynamic tests , 2013 .

[8]  L. Taner Tunç,et al.  Prediction of workpiece dynamics and its effects on chatter stability in milling , 2012 .

[9]  M. Szafarczyk,et al.  Selected Diagnostic Methods for Machine Tools Acceptance Tests , 1985 .

[10]  Andreas Archenti.  Model-Based Investigation of Machining Systems Characteristics : Static and Dynamic Stability Analysis , 2008 .

[11]  Yoshimi Ito,et al.  Modular Design for Machine Tools , 2008 .

[12]  Andreas Archenti,et al.  Recursive estimation of machine tool structure dynamic properties , 2010 .

[13]  Andreas Archenti,et al.  Dynamic parameter identification in nonlinear machining systems , 2013 .

[14]  D. Neumann.  FAULT DIAGNOSIS OF MACHINE-TOOLS BY ESTIMATION OF SIGNAL SPECTRA , 1992 .

[15]  Petre Stoica,et al.  Analysis of an output error identification algorithm , 1981, Autom..

[16]  Cornel Mihai Nicolescu,et al.  On-line identification and control of dynamic characteristics of slender workpieces in turning , 1996 .

[17]  Lutfi Taner Tunc,et al.  Effect of cutting conditions and tool geometry on process damping in machining , 2012 .

[18]  Krzysztof Jemielniak,et al.  Stability analysis in milling of flexible parts based on operational modal analysis , 2015 .

[19]  Recursive system identification , 2009 .

[20]  Metin Akay.  CHAPTER 11 – The Autoregressive Moving Average (ARMA) Method , 1994 .

[21]  Lennart Ljung,et al.  Analysis of a general recursive prediction error identification algorithm , 1981, Autom..

[22]  Constantinos Frangoudis,et al.  Controlling the dynamic characteristics of machining systems through consciously designed joint interfaces , 2014 .

[23]  Victor Songmene,et al.  Estimation of machine-tool dynamic parameters during machining operation through operational modal analysis , 2009 .

[24]  Christian Brecher,et al.  Avoiding chatter by means of active damping systems for machine tools , 2013 .

[25]  Yasunori Sakai,et al.  Dynamic characteristics of linear rolling bearings for machine tools , 2013 .

[26]  Alexander S. Poznyak.  13 – Parametric Identification , 2009 .

[27]  Eugene I. Rivin,et al.  Stiffness and Damping in Mechanical Design , 1999 .

[28]  Manfred Weck,et al.  Chatter Stability of Metal Cutting and Grinding , 2004 .

[29]  Erdem Ozturk,et al.  Stability and high performance machining conditions in simultaneous milling , 2013 .

[30]  Andreas Archenti,et al.  Recursive estimation of operational dynamic parameters in milling using acoustic signal , 2010 .

[31]  M. B. Priestley,et al.  Current developments in time series modelling , 1988 .

[32]  Yoshimi Ito,et al.  Position paper - fundamental issues in self-excited chatter in turning. Appendix – research into process damping by Altintas et al , 2013 .

[33]  Krzysztof Jemielniak,et al.  Suppression of self-excited vibration by the spindle speed variation method , 1984 .