Parametric optimization of MRR and surface roughness in wire electro discharge machining (WEDM) of D2 steel using Taguchi-based utility approach

BackgroundThis paper reports the effect of process parameters on material removal rate (MRR) and surface roughness (Ra) in wire electro discharge machining of AISI D2 steel.FindingsThe wire electro discharge machining characteristics of AISI D2 steel have been investigated using an orthogonal array of design. The pulse on time and servo voltage are the most significant parameter affecting MRR and surface roughness during WEDM process. The simultaneous performance characteristics MRR and surface roughness was optimized by Taguchi based utility approach. The machined surface hardness is higher than the bulk material hardness due to the repetitive quenching effect and contained various oxides in the surface recast layer.MethodsThe experiments were performed by different cutting conditions of pulse on time (Ton), pulse off time (Toff), servo voltage (SV) and wire feed (WF) by keeping work piece thickness constant. Taguchi L27 orthogonal array of experimental design is employed to conduct the experiments. Multi-objective optimization was performed using Taguchi based utility approach to optimize MRR and Ra.ResultsAnalysis of means and variance on to signal to noise ratio was performed for determining the optimal parameters. It reveals that the combination of Ton3, Toff1, SV1, WF2 parameter levels is beneficial for maximizing the MRR and minimizing the Ra simultaneously. The results indicated that the pulse on time is the most significant parameter affects the MRR and Ra. ConcludionsThe melted droplets, solidified debris around the craters, cracks and blow holes were observed on the machined surface for a higher pulse on time and lower servo voltage. Recast layer thickness increased with an increase in pulse on time duration. The machined surface hardness of D2 steel is increased due to the repetitive quenching effect and formation oxides on the machined surface.

[1]  L. Hwang,et al.  Machining Characteristics and Optimization of Machining Parameters of SKH 57 High-Speed Steel Using Electrical-Discharge Machining Based on Taguchi Method , 2006 .

[2]  Sanjay Agarwal,et al.  Optimization of Machining Parameters in WEDM of AISI D3 Steel Using Taguchi Technique , 2014 .

[3]  E. Uhlmann,et al.  Machining of micro/miniature dies and moulds by electrical discharge machining—Recent development , 2005 .

[4]  Anilesh Kumar,et al.  Technological Advancement in Electrical Discharge Machining with Powder Metallurgy Processed Electrodes: A Review , 2010 .

[5]  V. N. Gaitonde,et al.  Wire electric discharge machining characteristics of titanium nickel shape memory alloy , 2014 .

[6]  S. Basavarajappa,et al.  Wire Electro Discharge Machining Performance of TiNiCu Shape Memory Alloy , 2016, Silicon.

[7]  Nicolaas F. de Rooij,et al.  Microsystem technologies for implantable applications , 2007 .

[8]  Wolfgang Ehrfeld,et al.  State-of-the-art in microreaction technology : concepts, manufacturing and applications , 1999 .

[9]  I. K. Chopde,et al.  Optimization of Wire Electro Discharge Machining Parameters for Improving Surface Finish of Cryo-Treated Tool Steel Using DOE , 2014 .

[10]  Nixon Kuruvila,et al.  PARAMETRIC INFLUENCE AND OPTIMIZATION OF WIRE EDM OF HOT DIE STEEL , 2011 .

[11]  Jatinder Kumar,et al.  Optimization of WEDM process of pure titanium with multiple performance characteristics using Taguchi’s DOE approach and utility concept , 2013 .

[12]  I. K. Chopde,et al.  Investigations on Surface Characteristics of Heat Treated Tool Steel after Wire Electro-Discharge Machining , 2013 .

[13]  David K. Aspinwall,et al.  Rapid machining of hardened AISI H13 and D2 moulds, dies and press tools , 2003 .

[15]  Kamlakar P Rajurkar,et al.  Wire electro-discharge machining of titanium alloy , 2013 .

[16]  Gian Bhushan,et al.  Modelling and multi-objective optimization of process parameters of wire electrical discharge machining using non-dominated sorting genetic algorithm-II , 2012 .

[17]  R. S. Rana,et al.  Optimization of Electric Discharge Machining of M2 Tool Steel Using Grey Relational Analysis , 2015 .

[18]  M. K. Banerjee,et al.  Tool and Die Steels , 2001 .

[19]  Ulaş Çaydaş,et al.  Experimental study of wire electrical discharge machining of AISI D5 tool steel , 2004 .

[20]  J. Paulo Davim,et al.  Multiperformance Optimization in Turning of Free-Machining Steel Using Taguchi Method and Utility Concept , 2009, Journal of Materials Engineering and Performance.

[21]  Hesam Shahali,et al.  Optimization of surface roughness and thickness of white layer in wire electrical discharge machining of DIN 1.4542 stainless steel using micro-genetic algorithm and signal to noise ratio techniques , 2012 .

[22]  Vikram Singh,et al.  Optimization of WEDM Parameters Using Taguchi Technique and Response Surface Methodology in Machining of AISI D2 Steel , 2014 .

[23]  P. Dario,et al.  Non-traditional technologies for microfabrication , 1995 .