Corrosion behavior of austenitic stainless steels as a function of pH for use as bipolar plates in polymer electrolyte membrane fuel cells

Abstract Stainless steels (types 304 and 310S) were employed as bipolar plates for polymer electrolyte membrane fuel cells. For the cell operation, the decayed cell voltage was approximately 22 mV for the type 310S stainless steel after 1000 h operation, while that for type 304 stainless steel was about 46 mV. Corrosion products appeared on the cathode side bipolar plate for the type 304 stainless steel, while trace of corrosion was barely detected for type 310S stainless steel. In order to follow the pH on the bipolar plates during fuel cell operation, polarization tests were carried out for the type 310S stainless steel in synthetic solutions (0.05 M SO 4 2− (pH 1.2–5.5) + 2 ppm F − ) as a function of pH (1.2–5.5) at 353 K. We also examined the contact resistance between the stainless steel and carbon diffusion layer before and after polarization. X-ray photoelectron spectroscopic (XPS) analyses were carried out for comparison of the surface states of the steels after the polarization tests and cell operation. In the synthetic solutions with lower pHs (≤3.3), the films were thinner and were mainly composed by enriched with chromium oxide. Whereas, they mainly consisted of relatively thick iron oxide when the solution pH was higher (≥4.3). XPS analyses for the bipolar plate of type 310S stainless steel on cathode side after cell operation demonstrated pH gradient on the plate, that is, the thicker iron-rich surfaces presented relatively higher pH from the gas inlet to center area, and the thinner chromium-rich surface appeared with lower pH around the gas outlet.

[1]  Frano Barbir,et al.  PEM Fuel Cells , 2006 .

[2]  Heli Wang,et al.  Stainless steel as bipolar plate material for polymer electrolyte membrane fuel cells , 2003 .

[3]  Suzhen Luo,et al.  Electrochemical corrosion characteristics of type 316 stainless steel in simulated anode environment for PEMFC , 2003 .

[4]  H. Strehblow,et al.  Combined surface analytical and electrochemical study of the formation of passive layers on Fe/Cr alloys in 1 M NaOH , 1994 .

[5]  D. Costa,et al.  Influence of stainless steel surface treatment on the oxygen reduction reaction in seawater , 2001 .

[6]  Ching-Han Huang,et al.  Corrosion-resistant component for PEM fuel cells , 2004 .

[7]  Paul Leonard Adcock,et al.  New materials for polymer electrolyte membrane fuel cell current collectors , 1999 .

[8]  D. Landolt,et al.  Passive films on stainless steels—chemistry, structure and growth , 2003 .

[9]  Allen M. Hermann,et al.  Bipolar plates for PEM fuel cells: A review , 2005 .

[10]  H. Strehblow,et al.  A combined surface analytical and electrochemical study of the formation of passive layers on alloys in 0.5 M H2SO4 , 1995 .

[11]  P. Marcus,et al.  Corrosion Mechanisms in Theory and Practice , 1995 .

[12]  M. El-Basiouny,et al.  The polarization behaviour of FeCr alloys in acidic sulphate solutions in the active region , 1976 .

[13]  R. Borup,et al.  Design and Testing Criteria for Bipolar Plate Materials for Pem Fuel Cell Applications , 1995 .

[14]  C. Liu,et al.  Influence of pH on the passivation behavior of 254SMO stainless steel in 3.5% NaCl solution , 2007 .

[15]  P. Adcock,et al.  Stainless steel as a bipolar plate material for solid polymer fuel cells , 2000 .

[16]  Paul Leonard Adcock,et al.  Bipolar plate materials for solid polymer fuel cells , 2000 .

[17]  Heli Wang,et al.  Investigation of a Duplex Stainless Steel as Polymer Electrolyte Membrane Fuel Cell Bipolar Plate Material , 2005 .

[18]  N. Hara,et al.  Corrosion characteristics of Fe2O3Cr2O3 artificial passivation films under potentiostatic control , 1995 .

[19]  M. De Francesco,et al.  Nafion degradation in PEFCs from end plate iron contamination , 2003 .

[20]  A. Iversen.  Stainless steels in bipolar plates—Surface resistive properties of corrosion resistant steel grades during current loads , 2006 .

[21]  G. Cragnolino,et al.  Effect of pH on the Intergranular Stress Corrosion Cracking of Sensitized AISI 304 Stainless Steel in High Temperature Sulfate Solutions , 1987 .

[22]  W. Stickle,et al.  Handbook of X-Ray Photoelectron Spectroscopy , 1992 .

[23]  R. Hornung,et al.  Bipolar plate materials development using Fe-based alloys for solid polymer fuel cells , 1998 .

[24]  J. Kish,et al.  Anodic behaviour of stainless steel S43000 in concentrated solutions of sulphuric acid , 2003 .

[25]  John A. Turner,et al.  Ferritic stainless steels as bipolar plate material for polymer electrolyte membrane fuel cells , 2004 .

[26]  Ching-Han Huang,et al.  Stainless steel bipolar plates , 2005 .

[27]  D. Northwood,et al.  Effects of O2 and H2 on the corrosion of SS316L metallic bipolar plate materials in simulated anode and cathode environments of PEM fuel cells , 2007 .

[28]  Juncai Sun,et al.  Surface stability and conductivity of a high Cr and Ni austenitic stainless steel plates for PEMFC , 2006 .

[29]  D. Mahajan,et al.  Metal bipolar plates for PEM fuel cell—A review , 2007 .