Compressive behaviour of thin-skin stiffened composite panels with a stress raiser

Abstract The in-plane compressive behaviour of thin-skin stiffened composite panels with a stress concentrator in the form of an open hole or low velocity impact damage is examined analytically. Drop weight impact in laminated polymer composites causes matrix cracking, delaminations and fibre breakage, which together can seriously degrade the laminate compressive strength. Experimental studies, using ultrasonic C-scan images and X-ray shadow radiography, indicated that the overall damage resembles a hole. Under uniaxial compression loading, 0° fibre microbuckling surrounded by delamination grows laterally (like a crack) from the impact site as the applied load is increased. These local buckled regions continued to propagate, first in discrete increments and then rapidly at failure load. The damage pattern is very similar to that observed in laminated plates with open holes loaded in compression. Because of this resemblance, a fracture mechanics model, developed initially to predict notched compressive strength, was applied to estimate the compression-after-impact (CAI) strength of a stiffened panel; in the analysis the impact damage is replaced with an equivalent open hole. Also, the maximum stress failure criterion is employed to estimate the residual compressive strength of the panel. The unnotched compressive strength of the composite laminate required in the analysis is obtained from a three-dimensional stability theory of deformable bodies. The influence of the stiffener on the compressive strength of the thin-skin panel is examined and included in the analysis. A good agreement between experimental measurements and predicted values for the critical failure load is obtained.

[1]  Norman A. Fleck,et al.  Failure Prediction Technique for Compression Loaded Carbon Fibre-Epoxy Laminate with Open Holes , 1991 .

[2]  Constantinos Soutis.  Damage tolerance of open-hole CFRP laminates loaded in compression , 1994 .

[3]  G.A.O. Davies,et al.  Buckling and postbuckling of composite structures , 1995 .

[4]  I. A. Guz,et al.  Compressive fracture of non-linear composites undergoing large deformations , 2001 .

[5]  I. A. Guz,et al.  A 3-D stability theory applied to layered rocks undergoing finite deformations in biaxial compression , 2001 .

[6]  A. Guz.  Fundamentals of the Three-Dimensional Theory of Stability of Deformable Bodies , 1999 .

[7]  Michael P. Nemeth,et al.  Buckling and Postbuckling Behavior of Laminated Composite Plates With a Cutout , 1995 .

[8]  Constantinos Soutis,et al.  Strength prediction of CFRP plates with a hole under biaxial compression-tension , 1998 .

[9]  Dawn C. Jegley,et al.  Behavior of Compression-Loaded Composite Panels with Stringer Terminations and Impact Damage , 1998 .

[10]  C. Soutis.  Compressive Strength of Unidirectional Composites: Measurement and Prediction , 1997 .

[11]  Chang-Sun Hong,et al.  Postbuckling and failure of stiffened composite panels under axial compression , 1998 .

[12]  Constantinos Soutis,et al.  Prediction of the post-impact compressive strength of CFRP laminated composites , 1996 .

[13]  Hiroshi Tada,et al.  The stress analysis of cracks handbook , 2000 .

[14]  Ozden O. Ochoa,et al.  A Parametric Study of Variables That Affect Fiber Microbuckling Initiation in Composite Laminates: Part 1-Analyses , 1992 .

[15]  Seng-Chuan Tan,et al.  Stress Concentrations in Laminated Composites , 1994 .

[16]  Arthur W. Leissa,et al.  An Overview of Composite Plate Buckling , 1987 .

[17]  A. N. Guz,et al.  Constructing the Three-Dimensional Theory of Stability of Deformable Bodies , 2001 .

[18]  Constantinos Soutis.  Compression testing of pultruded carbon fibre-epoxy cylindrical rods , 2000 .

[19]  C. Dawn.  Effect of Low-Speed Impact Damage and Damage Location on Behavior of Composite Panels , 1992 .

[20]  Norman A. Fleck,et al.  Static Compression Failure of Carbon Fibre T800/924C Composite Plate with a Single Hole , 1990 .

[21]  I. H. Marshall.  Analysis and design studies , 1987 .

[22]  R. Heywood.  Designing by photoelasticity , 1952 .

[23]  A. N. Guz,et al.  Description and Study of Some Nonclassical Problems of Fracture Mechanics and Related Mechanisms , 2000 .

[24]  S. Singh,et al.  Impact damage resistance and tolerance of stringer stiffened composite structures , 1999 .

[25]  S. Timoshenko,et al.  Theory of elasticity , 1975 .

[26]  Grant P. Steven,et al.  Buckling mode transition in hat-stiffened composite panels loaded in uniaxial compression , 1997 .

[27]  Constantinos Soutis,et al.  Effect of off-axis ply orientation on 0°-fibre microbuckling , 1999 .

[28]  Constantinos Soutis,et al.  Continuum fracture theory for layered materials: investigation of accuracy , 1999 .

[29]  R. Peterson,et al.  Stress Concentration Factors , 1974 .