Active Control of Elastodynamic Vibrations of a Four-Bar Mechanism System With a Smart Coupler Link Using Optimal Multivariable Control: Experimental Implementation

This paper presents an experimental investigation on active control of the elastodynamic response of a four-bar (4R) mechanism system using smart materials featuring piezoelectric sensor/actuator (S/A) pairs and multivariable optimal control. The experimental 4R mechanism is made such that its coupler link is flexible, its follower link is slightly less flexible and its crank is relatively rigid. Two thin plate-type piezoceramic S/A pairs are bonded to the flanks of the coupler link at the high strain locations corresponding to the first and second vibration modes. Based on the optimal multivariable control theory, a controller which consists of a linear quadratic regulator (LQR) and a Luenberger observer as a state estimator is designed and implemented. The results of the experimental investigation prove that in order to prevent high mode excitations, the controller design should be based on the modes representing vibrations of all components comprising the mechanism system rather than the modes corresponding to the link to which the S/A pairs are bonded. Response amplitude attenuation ratios up to 50 percent are achieved and high mode excitations are prevented.

[1]  Cemil Bagci,et al.  Fatique design of machine elements using the “Bagci line” defining the fatigue failure surface line (mean stress diagram) , 1981 .

[2]  B. Anderson,et al.  Optimal control: linear quadratic methods , 1990 .

[3]  Chia-Chi Sung,et al.  Active control of torsional vibration using piezoceramic sensors andactuators , 1990 .

[4]  Brian S. Thompson,et al.  The synthesis of flexible linkages by balancing the tracer point quasi-static deflections using microprocessor and advanced materials technologies , 1985 .

[5]  W. A. Thornton,et al.  Optimality Criterion Techniques Applied to Mechanical Design , 1978 .

[6]  Brian S. Thompson,et al.  The design of robots and intelligent manipulators using modern composite materials , 1985 .

[7]  M. Balas,et al.  Feedback control of flexible systems , 1978 .

[8]  S. Poh,et al.  Performance of an active control system with piezoelectric actuators , 1988 .

[9]  J. L. Fanson,et al.  Active-member control of precision structures , 1989 .

[10]  Ephrahim Garcia,et al.  A Self-Sensing Piezoelectric Actuator for Collocated Control , 1992 .

[11]  T. Bailey,et al.  Distributed Piezoelectric-Polymer Active Vibration Control of a Cantilever Beam , 1985 .

[12]  E. Crawley,et al.  Use of piezoelectric actuators as elements of intelligent structures , 1987 .

[13]  C. Y. Liao,et al.  Vibration Suppression of Flexible Linkage Mechanisms Using Piezoelectric Sensors and Actuators , 1991 .

[14]  M. Preiswerk,et al.  An analysis of vibration control using piezoceramics in planar flexible-linkage mechanisms , 1994 .

[15]  Y. C. Chen,et al.  Vibration Control of the Elastodynamic Response of High-Speed Flexible Linkage Mechanisms , 1991 .

[16]  W. Hwang,et al.  Vibration Control of a Laminated Plate with Piezoelectric Sensor/Actuator: Finite Element Formulation and Modal Analysis , 1993 .

[17]  Nesbitt W. Hagood,et al.  Self-sensing piezoelectric actuation - Analysis and application to controlled structures , 1992 .

[18]  Nesbitt W. Hagood,et al.  Modelling of Piezoelectric Actuator Dynamics for Active Structural Control , 1990 .

[19]  William L. Cleghorn,et al.  Optimum design of high-speed flexible mechanisms , 1981 .

[20]  Nesbitt W. Hagood,et al.  Damping of structural vibrations with piezoelectric materials and passive electrical networks , 1991 .

[21]  Seung-Bok Choi,et al.  Vibration control of flexible linkage mechanisms using piezoelectric films , 1994 .