Bubble formation during horizontal gas injection into downward-flowing liquid

Bubble formation during gas injection into turbulent downward-flowing water is studied using high-speed videos and mathematical models. The bubble size is determined during the initial stages of injection and is very important to turbulent multiphase flow in molten-metal processes. The effects of liquid velocity, gas-injection flow rate, injection hole diameter, and gas composition on the initial bubble-formation behavior have been investigated. Specifically, the bubble-shape evolution, contact angles, size, size range, and formation mode are measured. The bubble size is found to increase with increasing gas-injection flow rate and decreasing liquid velocity and is relatively independent of the gas injection hole size and gas composition. Bubble formation occurs in one of four different modes, depending on the liquid velocity and gas flow rate. Uniform-sized spherical bubbles form and detach from the gas injection hole in mode I for a low liquid speed and small gas flow rate. Modes III and IV occur for high-velocity liquid flows, where the injected gas elongates down along the wall and breaks up into uneven-sized bubbles. An analytical two-stage model is developed to predict the average bubble size, based on realistic force balances, and shows good agreement with measurements. Preliminary results of numerical simulations of bubble formation using a volume-of-fluid (VOF) model qualitatively match experimental observations, but more work is needed to reach a quantitative match. The analytical model is then used to estimate the size of the argon bubbles expected in liquid steel in tundish nozzles for conditions typical of continuous casting with a slide gate. The average argon bubble sizes generated in liquid steel are predicted to be larger than air bubbles in water for the same flow conditions. However, the differences lessen with increasing liquid velocity.

[1]  Hua Bai,et al.  Turbulent flow of liquid steel and argon bubbles in slide-gate tundish nozzles: Part I. model development and validation , 2001 .

[2]  K. Mukai,et al.  Influence of Wettability on the Behavior of Argon Bubbles and Fluid Flow inside the Nozzle and Mold , 1999 .

[3]  C. W. Hirt,et al.  Volume of fluid (VOF) method for the dynamics of free boundaries , 1981 .

[4]  R. Guthrie.  Engineering in Process Metallurgy , 1992 .

[5]  S. Thompson.  The Chem Tech , 1973 .

[6]  B. Launder,et al.  The numerical computation of turbulent flows , 1990 .

[7]  Hua Bai,et al.  Behavior of Argon Bubbles during Continuous Casting of Steel , 1997 .

[8]  G. A. Irons,et al.  Bubble formation at nozzles in pig iron , 1978 .

[9]  S. L. Soo,et al.  Multiphase fluid dynamics , 1990 .

[10]  Tetsuya Fujii,et al.  Numerical analysis of fluid flow in the continuous casting mold by a bubble dispersion model , 1991 .

[11]  Brian G. Thomas,et al.  Simulation of Argon Gas Flow Effects in a Continuous Slab Caster , 1994 .

[12]  R. Winterton.  Sizes of bubbles produced by dissolved gas coming out of solution on the walls of pipes in flowing systems , 1972 .

[13]  Y. Kawase,et al.  Formation of drops and bubbles in flowing liquids , 1981 .

[14]  R. Kumar,et al.  The Formation of Bubbles and Drops , 1970 .

[15]  Koichi Terasaka,et al.  Bubble formation at a single orifice in highly viscous liquids , 1990 .

[16]  Peter C. Hayes,et al.  Prediction of the Optimum Bubble Size for Inclusion Removal from Molten Steel by Flotation , 1996 .

[17]  Manabu Iguchi,et al.  Measurement of bubble characteristics in a molten iron bath at 1600 °C using an electroresistivity probe , 1995 .

[18]  S. C. Chuang,et al.  Bubble Formation Due to a Submerged Capillary Tube in Quiescent and Coflowing Streams , 1970 .

[19]  R. Clift,et al.  Bubbles, Drops, and Particles , 1978 .

[20]  M. Larrecq,et al.  Experimental and theoretical analysis of gas and metal flows in submerged entry nozzles in continuous casting , 1996 .

[21]  M. Iguchi,et al.  X-ray fluoroscopic observation of bubble characteristics in a molten iron bath , 1995 .

[22]  R. Guthrie,et al.  Communications: X-Ray Cinematographic Observations of Gas Injection into Liquid Metals , 1978 .

[23]  Y. Nakajima,et al.  Behavior of bubbles formed from a submerged orifice under high system pressure , 1992 .

[24]  Koichi Terasaka,et al.  Bubble formation under constant-flow conditions , 1993 .

[25]  W. V. Pinczewski,et al.  The formation and growth of bubbles at a submerged orifice , 1981 .

[26]  M. Sano,et al.  Bubble Formation from Single Nozzles in Liquid Metals , 1974 .